Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Free wheeling hubs

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Post Reply
Posts: 365
Joined: Mon Aug 18, 2003 1:03 am
Location: Perth

Free wheeling hubs

Post by Shark »

As some of you know i aint got these onme rig and am seriously considering putting some on.

Is it difficult??

Can i take em off a wrecking car with no hassles??


Marc
Posts: 677
Joined: Mon Nov 18, 2002 10:00 am
Location: Melbourne

Post by roly »

easy as undoing the 6 allen key bolts
08 340kw HSV Maloo 6.2L
John Roly
Melbourne Again
Posts: 365
Joined: Mon Aug 18, 2003 1:03 am
Location: Perth

Post by Shark »

Okay i am picking up a pair of these and i want to know if there is anything else i need to know when taking them off the wrecking car and putting them onto mine.

NB Remember that my car does not have them at the moment.

MArc
Posts: 4275
Joined: Thu Dec 19, 2002 2:12 pm
Location: Sydney

Post by ozy1 »

when you undo the 6 bolts and take off the locking hub, make sure you get all of it, you will have the locakable housing, then there is another bit that slides onto your drive shaft, without this, it will not lock,
Posts: 2492
Joined: Sun Nov 24, 2002 8:57 pm
Location: Melbourne

Post by bazzle »

AND the circlip

Bazzle
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

there is also 2 shims ( steel rings) inside the actual hub, it may pay to grab these too incase your front diff setup is differant.

Kingy
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Posts: 365
Joined: Mon Aug 18, 2003 1:03 am
Location: Perth

Post by Shark »

Okay guys i now have a second hand set of these which i would like to install onto my car which doesnt have them at the moment.

I took the locking hubs off the wrecking car and the only thing that came off was the actual locking hub itself and nothing else. I Had a quick look at mine and instead of having a locking hub it just has a cover but with the cover off it looks very similar to the other car.

Could i do any damage to my car when putting these on?? AND is there an easy way to check wether they are working or not once i have put them on my car??

Gonna give it a go to put them on tomorrow.

Cheers
Marc
Posts: 4275
Joined: Thu Dec 19, 2002 2:12 pm
Location: Sydney

Post by ozy1 »

after you have put them on, jack up the whole front of the car, and with them unlocked spin one wheel, and make sure the other is not moving, then, lock both hubs, and spin one wheel again, with the hubs locked both should spin,

just make sure that when you put them on, it is always best to apply a bit of grease inside the locking hub, and also it doesnt hurt to make a gasket to go between the 2 surfaces, this will minimise water entry, which bearing hate.
Posts: 365
Joined: Mon Aug 18, 2003 1:03 am
Location: Perth

Post by Shark »

If these hubs are stuffed for some reason could that damage my car in any way??

Marc
Posts: 2492
Joined: Sun Nov 24, 2002 8:57 pm
Location: Melbourne

Post by bazzle »

just make sure that when you put them on, it is always best to apply a bit of grease inside the locking hub,


Only use a smear. Grease can cause huns to not wind in far enough (Hydraulic lock)

Bazzle :roll:
Posts: 5060
Joined: Tue Apr 08, 2003 7:28 pm
Location: Narellan Vale, Sydney

Post by Screwy »

U cannot cause any real damage as all they do is sit on your CV/ axle and wrap around it. if they work u will know it from jacking the car up as previosly described. If they dont work then when they are locked your front shaft wont spin and only one wheel will spin. just means that they havnt locked. thats about all that can happen.

screwy
TUFF TRUCK TEAM OPPOSITE LOCK Proudly Sponsored By:

Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Posts: 365
Joined: Mon Aug 18, 2003 1:03 am
Location: Perth

Post by Shark »

Another thing i am concerned with is my car must be " Locked " now becasue obviously i dont have the hubs on now and its locked already.

Confusing
Marc
Posts: 2492
Joined: Sun Nov 24, 2002 8:57 pm
Location: Melbourne

Post by bazzle »

Just leave transfer in 2wd and all will be OK.

Bazzle
Posts: 569
Joined: Sun Jan 11, 2004 11:36 am
Location: Sunshine Coast QLD

Post by Mark2 »

You probably know this already, but dont do what I did once and change into 4WD on the move when the hubs are unlocked. I came off the beach, unlocked the hubs, went back on after lunch and forgot that I had unlocked the hubs.

I still havent forgotten the sound it made............
Posts: 4275
Joined: Thu Dec 19, 2002 2:12 pm
Location: Sydney

Post by ozy1 »

Mark2 wrote:You probably know this already, but dont do what I did once and change into 4WD on the move when the hubs are unlocked. I came off the beach, unlocked the hubs, went back on after lunch and forgot that I had unlocked the hubs.

I still havent forgotten the sound it made............


it only makes that sound until the front shaft is lockedin and spinning as quick as the rear :twisted:
Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests