Hi all,
Can you install a 10,000lb Warn winch in an ARB bar after it has been fitted to a GU Patrol? I know you can get a 9000lb in and out but the 10,000 is a big beast!!
Leroy
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
10,000lb Warn in ARB bar on GU Patrol
I just went out and had a look at mine (bar has been modded to suit 2" body lift in the coil cab) and I can't see how you'd get it out without removing the bar.
I run side rails and have 2 bars - 1 to suit the 10,000lb low mount that is in the car for general use when the ute is loaded to the hilt with camping gear, etc and an ARB bar that has been modified to take a high mount that was used for comp style stuff. It takes longer to swap over the wiring on the winches than it does to remove 1 bar and bolt on the other, so I wouldn't be too worried about having to drop the bar.
The winch is pretty heavy (and too expensive) to be juggling in fingertips through a tight fitting gap anyway.
I run side rails and have 2 bars - 1 to suit the 10,000lb low mount that is in the car for general use when the ute is loaded to the hilt with camping gear, etc and an ARB bar that has been modified to take a high mount that was used for comp style stuff. It takes longer to swap over the wiring on the winches than it does to remove 1 bar and bolt on the other, so I wouldn't be too worried about having to drop the bar.
The winch is pretty heavy (and too expensive) to be juggling in fingertips through a tight fitting gap anyway.
I'm not very good looking, so I guess I better be useful . . .
Posts: 1931
Joined: Sun Jun 22, 2003 10:29 am
Joined: Sun Jun 22, 2003 10:29 am
Location: Everything 4WD, 86 Camms Rd Cranbourne
Contact:
Unless I misunderstood your question, you were asking whether it can be fitted without removing the bar not whether or not it will fit.
They definitely fit but I still don't reckon you could get it in or out without removing the bar first. For reference, my bar is one of the original, deluxe ARB bars, not one of the newer ones that is folded more like the 100 series cruiser bars.
They definitely fit but I still don't reckon you could get it in or out without removing the bar first. For reference, my bar is one of the original, deluxe ARB bars, not one of the newer ones that is folded more like the 100 series cruiser bars.
I'm not very good looking, so I guess I better be useful . . .
Posts: 1931
Joined: Sun Jun 22, 2003 10:29 am
Joined: Sun Jun 22, 2003 10:29 am
Location: Everything 4WD, 86 Camms Rd Cranbourne
Contact:
yep, sorry, misunder stood the Q. I can't see how you would fit it in with out taking the bar off. I think the hassle you would have wouldn't be worth it even if you could
My club
www.vfwdc.com
My store
Everything 4WD
86 Camms Road Cranbourne
www.everything4wd.com.au
sales@everything4wd.com.au
Phone: 03 59955055
www.vfwdc.com
My store
Everything 4WD
86 Camms Road Cranbourne
www.everything4wd.com.au
sales@everything4wd.com.au
Phone: 03 59955055
Who is online
Users browsing this forum: No registered users and 149 guests