Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Cam Belt Tension , HELP !!

Tech Talk for Suzuki owners.

Moderators: lay80n, sierrajim

Forum rules
Post Reply
Posts: 3825
Joined: Wed Nov 06, 2002 8:42 pm
Location: in the sky , its a bird , its a plane ! No its super MOOSE !!!

Cam Belt Tension , HELP !!

Post by moose »

since doing my 1.6 block/1.3 head motor conversion
I cant get good tension on the cam belt !! :?

any 1 know of a fix ??

any advice , greatly appreciated !!! :D
(in regards to my complaint !! :armsup: )
MissForbyNoob wrote:
and one day i'll just become a worthless housewife.
Top
Posts: 6229
Joined: Thu Dec 12, 2002 10:37 am
Location: melbourne victoria australia

Contact:
Contact christover1

Re: Cam Belt Tension , HELP !!

Post by christover1 »

moose wrote:since doing my 1.6 block/1.3 head motor conversion
I cant get good tension on the cam belt !! :?

any 1 know of a fix ??

any advice , greatly appreciated !!! :D
(in regards to my complaint !! :armsup: )


probably mismatched pulleys and/or need a shorter cam belt. even between 2 standard 1.0 litre engines, there was a big difference in cam timing parts (ie crank pulleys were 2 teeth different and 4 on the cam pulleys, and belts were different lenghs). worth a look, christover
4WD SUZUKI CLUB VICTORIA
http://www.vic.suzuki4wd.com/forum/
Top
Posts: 115
Joined: Tue Oct 21, 2003 5:27 pm
Location: Sydney

Post by No Idea »

What's the diameter of the tensioner brg?
Is it the 1.3 or the 1.6 one?
Top
Posts: 3825
Joined: Wed Nov 06, 2002 8:42 pm
Location: in the sky , its a bird , its a plane ! No its super MOOSE !!!

Post by moose »

the tensioners are both the same size !!!!

is a 1.6 head taller ??

is there a shorter belt available ??

:?: :?
MissForbyNoob wrote:
and one day i'll just become a worthless housewife.
Top
Posts: 6229
Joined: Thu Dec 12, 2002 10:37 am
Location: melbourne victoria australia

Contact:
Contact christover1

Post by christover1 »

make sure cam pulley has twice the teeth of the crank pulley, 2:1 is only ratio that aint gonna destruct the motor.
I put a 2nd hand head off an old one litre motor onto mine, luckily I noticed one had 18:36 the other 20:40 ratio, so had to chang my original cam pulley onto the new head. both cam belts appeared to be same length, but I never counted them.
I have had an adjuster that was assembled wrongly, so thats worth a look into, too,
christover
4WD SUZUKI CLUB VICTORIA
http://www.vic.suzuki4wd.com/forum/
Top
Posts: 169
Joined: Tue Sep 23, 2003 1:37 pm
Location: New Zealand home of the warriors

Post by Luigi Malone »

Fix #1 Get an engineer to press fit a larger diameter wheel over the top of what you have.

Fix #2 Move the adjuster (chuck the springs) down wards and relocate the bolt to one of the existing front bolts. And or, elongate the hole where the bolt goes through.

These belts are hard to tighten at the best of times. I think cam belts need to be TIGHT. I have both of the above fixes, but feel I still need more.
I only had the jockey wheel diameter increased by a couple of mm, needed more like 4 or 5mm.
LM.
It's better to have LIVED for a day than to have EXISTED for a hundred years.
Top
Post Reply

Return to “Suzuki”

Who is online

Users browsing this forum: Bing [Bot] and 0 guests