Hoping someone can help me with this problem.
I had my car into the garage yesterday to get a weld strengthened on the exaust. When I drove it home I noticed that the "super select" indicators on the dash were flashing (like they do when you change from or to 4WD).
Iv'e driven about 10 Ks since then, in 2WD and in 4WD high and low.
When I change to 4WD, the lights stay on as per normal, when I change back to 2WD they continue to flash on and off.
Does'nt seem to be serious but I don't have a clue where to start looking.
Thanks, Neil
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Super Select indicators flashing???
Moderator: -Scott-
Super Select indicators flashing???
It's time for my pill!
Neil sounds like it is an electrical issue.
Most likely the free wheel engage switch either needs replacing or cleaning (bad connection).
This is located next to the actuator rod and if you remove your bashplates can see it clearly. This is the first place to start rather than diving in and replacing the 4x4 ECU behind the dash. Also pays to check the two vacuum solenoids (located just behind the air filter on the wheel tub) to make sure none of the hoses are split or leaking and all connections are good. It only takes a small amount of crap in the wrong place to upset this system so it pays to acquaint yourself with it.
If you buy a Gregory's manual (No- 510) it explains it pretty well. Most of the flashing lights issue's are more annoying than anything else.
Most likely the free wheel engage switch either needs replacing or cleaning (bad connection).
This is located next to the actuator rod and if you remove your bashplates can see it clearly. This is the first place to start rather than diving in and replacing the 4x4 ECU behind the dash. Also pays to check the two vacuum solenoids (located just behind the air filter on the wheel tub) to make sure none of the hoses are split or leaking and all connections are good. It only takes a small amount of crap in the wrong place to upset this system so it pays to acquaint yourself with it.
If you buy a Gregory's manual (No- 510) it explains it pretty well. Most of the flashing lights issue's are more annoying than anything else.
Bitsamissin, thanks for the reply.
Am sure it's electrical, as everything is working normally, apart from this disco on the dash.
Have got a Gregory's 510, and spent yesterday (Monday) tracing the various 2WD, 4WD switches on the vehicle, so I now have an idea of where most of them are, (did not remove bash plates).
Have booked the car into above mentioned garage tomorrow, (there was no problem till they got to it) for them to have a look at it.
If they cannot fix it I will go through your suggestions 1X1.
Again, thanks for the help.
Neil
Feel sorry for Pajpwr, just went through something similar with CV joints on my sons Suby.
Am sure it's electrical, as everything is working normally, apart from this disco on the dash.
Have got a Gregory's 510, and spent yesterday (Monday) tracing the various 2WD, 4WD switches on the vehicle, so I now have an idea of where most of them are, (did not remove bash plates).
Have booked the car into above mentioned garage tomorrow, (there was no problem till they got to it) for them to have a look at it.
If they cannot fix it I will go through your suggestions 1X1.
Again, thanks for the help.
Neil
Feel sorry for Pajpwr, just went through something similar with CV joints on my sons Suby.
It's time for my pill!
No it's not better than a factory manual overall.
But it does have a good section on the 4x4 flashing lights.
I have a Haynes, Chiltons but overall the Gregory's is the best out of em.
http://www.gregorys-online.com/greghome.asp is their website but it seems to be down at the moment.
I don't have a factory manual but I hope it comes online through Jason's site.
But it does have a good section on the 4x4 flashing lights.
I have a Haynes, Chiltons but overall the Gregory's is the best out of em.
http://www.gregorys-online.com/greghome.asp is their website but it seems to be down at the moment.
I don't have a factory manual but I hope it comes online through Jason's site.
Who is online
Users browsing this forum: No registered users and 13 guests