Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Guide to tweaking Tdi's
Moderator: Micka
Guide to tweaking Tdi's
The Land Rover Tdi is not a bad motor, reasonable power and torque (as long as the turbo is on) and bloody good fuel economy. That said, it could certainly do with a bit more oomph, particularly after you start adding weight to the vehicle or add bigger tyres.
I've recently upgraded the bald 29" road tyres that came with mine with some 235/85/16 Muddies (courtesy of 4wdTV ) and noticed that it lacked a fair bit mid and upper range after the upgrade. Being used to the V8 in the Rangie, i decided that something had to be done......
The tdi utilises a Bosch VE injection pump which is used on a number of diesel vehicles. There are some very easy mods which can be done to these which have a marked impact on performance. Note that these mods will raise your EGT and should only be performed if you know what you're doing, if you f*ck anything up, you could destroy your motor!!!
Firstly, check out this image....
This shows what the the injection pump looks like, note where the smoke adjustment screw is and the diaphragm, these are the important bits.
On this top bit is something that looks like a welsh plug, this can be removed by levering out with a small screw driver. Under this plug is the smoke screw which is a T25 torx bit surrounded by a 13mm locknut. Undo the nut, and now mark the position of the torx screw. This is can be quite tight.
Turn this screw between 1 and 1.5 turns clockwise. I turned mine 1 full rotation (360 degrees) to err on the safe side before i install an EGT gauge. Adjusting this will improve the low manifold boost pressure responsiveness.
The next step is to remove the cover held down by four screws (see above photo). This will allow access to the diaphagm and star wheel.
Once removed mark the position of the diaphagm. The diaphragm can now be pulled out. You will note that the bottom of the pin is not symmetrical. By rotating the diaphragm approximately 90 degrees clockwise you will improve full throttle response.
While you have the diaphagm removed you should be able to see the starwheel. Rotating this clockwise increases the tension on the spring which improves the fuel load delivery rate. Again, note the position of the star wheel. Rotate approximately 180 degrees.
Now put back together and see how much it smokes. There should not be much black smoke as this indicates unburnt diesel and most likely high EGT's. These settings can be tweaked more but do so at your own risk. High EGT's will kill a diesel! You have been warned!
Check out LRE for further discussion on this. I got most of my info from there but a lot of it was not very clear.
Also, for more info....
http://dodgeram.org/tech/dsl/more_power/Power_ve.htm
http://www.cs.rochester.edu/u/jag/vw/en ... jpump.html
Good luck, it will really transform your Tdi. Mine goes as good as a Td5 now and is much safer and more enjoyable to drive.
I've recently upgraded the bald 29" road tyres that came with mine with some 235/85/16 Muddies (courtesy of 4wdTV ) and noticed that it lacked a fair bit mid and upper range after the upgrade. Being used to the V8 in the Rangie, i decided that something had to be done......
The tdi utilises a Bosch VE injection pump which is used on a number of diesel vehicles. There are some very easy mods which can be done to these which have a marked impact on performance. Note that these mods will raise your EGT and should only be performed if you know what you're doing, if you f*ck anything up, you could destroy your motor!!!
Firstly, check out this image....
This shows what the the injection pump looks like, note where the smoke adjustment screw is and the diaphragm, these are the important bits.
On this top bit is something that looks like a welsh plug, this can be removed by levering out with a small screw driver. Under this plug is the smoke screw which is a T25 torx bit surrounded by a 13mm locknut. Undo the nut, and now mark the position of the torx screw. This is can be quite tight.
Turn this screw between 1 and 1.5 turns clockwise. I turned mine 1 full rotation (360 degrees) to err on the safe side before i install an EGT gauge. Adjusting this will improve the low manifold boost pressure responsiveness.
The next step is to remove the cover held down by four screws (see above photo). This will allow access to the diaphagm and star wheel.
Once removed mark the position of the diaphagm. The diaphragm can now be pulled out. You will note that the bottom of the pin is not symmetrical. By rotating the diaphragm approximately 90 degrees clockwise you will improve full throttle response.
While you have the diaphagm removed you should be able to see the starwheel. Rotating this clockwise increases the tension on the spring which improves the fuel load delivery rate. Again, note the position of the star wheel. Rotate approximately 180 degrees.
Now put back together and see how much it smokes. There should not be much black smoke as this indicates unburnt diesel and most likely high EGT's. These settings can be tweaked more but do so at your own risk. High EGT's will kill a diesel! You have been warned!
Check out LRE for further discussion on this. I got most of my info from there but a lot of it was not very clear.
Also, for more info....
http://dodgeram.org/tech/dsl/more_power/Power_ve.htm
http://www.cs.rochester.edu/u/jag/vw/en ... jpump.html
Good luck, it will really transform your Tdi. Mine goes as good as a Td5 now and is much safer and more enjoyable to drive.
Last edited by TuffRR on Sun Jan 30, 2005 10:02 pm, edited 1 time in total.
Range Rover - 4.4 V8, MD Crawler Box, F&R Lockers, 35" Centipedes, 4" lift. Overqualified WebWheeler!!!
Discovery - Bling touring stuff!
Discovery - Bling touring stuff!
tdi tweaks
I do lots of them, and I would again stress the importance of a EGT Gauge(Pyrometer) when setting up.
Check out www.thermoguard.com.au he is based in ALice springs and has some excellent gear, He initially developed it for his own Tdi Disco.
DONT BE GREEDY!!!!
Too much heat will kill these engines, melt exhaust turbines and ruin the hardened pistons in the Tdi VERY QUICKLY.
Also check out www.bankspower.com in the US.
Gale Banks has done some awesome Hi-Po diesel tuning and has a good write up on max allowable EGT's etc.
I usually findout what sort of use the customer wants out of their Tdi first, IE towing, street drags, etc ( I'm not kidding, 205R16's and a defender transfer case ratio in a lightened auto Tdi disco IS very quick through the gears!) and tailor fuelling to suit.
The intercooler option is a good idea, with anything over 16 PSi boost and a sustained 700DegC EGT, then bigger coolers are required.
I usually aim for a sustained duty cycle of around 600degC, as most aren't likely to spend Too much time at these full load conditions, and must be measured UPSTREAM of the Turbo charger.
Check out the above websites for more info.
JC
Check out www.thermoguard.com.au he is based in ALice springs and has some excellent gear, He initially developed it for his own Tdi Disco.
DONT BE GREEDY!!!!
Too much heat will kill these engines, melt exhaust turbines and ruin the hardened pistons in the Tdi VERY QUICKLY.
Also check out www.bankspower.com in the US.
Gale Banks has done some awesome Hi-Po diesel tuning and has a good write up on max allowable EGT's etc.
I usually findout what sort of use the customer wants out of their Tdi first, IE towing, street drags, etc ( I'm not kidding, 205R16's and a defender transfer case ratio in a lightened auto Tdi disco IS very quick through the gears!) and tailor fuelling to suit.
The intercooler option is a good idea, with anything over 16 PSi boost and a sustained 700DegC EGT, then bigger coolers are required.
I usually aim for a sustained duty cycle of around 600degC, as most aren't likely to spend Too much time at these full load conditions, and must be measured UPSTREAM of the Turbo charger.
Check out the above websites for more info.
JC
'92 Rangie Sherwood/turbo intercooled isuzu4BD1 /ACE/ full leather/2.5" exh/2.5" body lift/DeCarbon shocks/LR tanks/LT95 back in and OK now, Sals conversion soon...
TuffRR wrote:
I got it done for $9.96 (had to buy a bigger screwdriver for the diaphragm cover).
nice but i did mine on a dyno and saw where i got the results i picked up
i went from 34kw to 55kw at the rear wheels. plus i made sure EGT were down
---------------------------------------------
04 GU TD6 wagon with some ARB stuff
---------------------------------------------
Morkz Media Web and Graphic Design
Also webhosting and domain registration.
04 GU TD6 wagon with some ARB stuff
---------------------------------------------
Morkz Media Web and Graphic Design
Also webhosting and domain registration.
Some good links there Justin, the thermogaurd looks like a good product.
Also, what sort of intercoolers do you use when upgrading? Do you find that fuel consumption remains similar after the upgrades (ignoring the tendency to put the boot in a bit more).
Also, what sort of intercoolers do you use when upgrading? Do you find that fuel consumption remains similar after the upgrades (ignoring the tendency to put the boot in a bit more).
Range Rover - 4.4 V8, MD Crawler Box, F&R Lockers, 35" Centipedes, 4" lift. Overqualified WebWheeler!!!
Discovery - Bling touring stuff!
Discovery - Bling touring stuff!
Also notice in the 3rd photo , from marks that the fuel pin has made on the taper, that the taper pin is not travelling fully down. The stroke can be increased by removing/modifying the stop/spacer below the diaphram.
I have the thermoguard kits for my 300TDi and 4BD1T diesels. They are pretty good IMHO. Especially for 300TDi discos - thermocouple mounts using EGR blanking plate and digital display fits neatly into disco dash.
I have the thermoguard kits for my 300TDi and 4BD1T diesels. They are pretty good IMHO. Especially for 300TDi discos - thermocouple mounts using EGR blanking plate and digital display fits neatly into disco dash.
John
Bush65 wrote: I have the thermoguard kits for my 300TDi and 4BD1T diesels. They are pretty good IMHO. Especially for 300TDi discos - thermocouple mounts using EGR blanking plate and digital display fits neatly into disco dash.
Whereabouts have you mounted the display? I've had a quick look and no where obvious sticks out. It looks like it could be quite conspicuous and i dont want it distracting me at night.
Range Rover - 4.4 V8, MD Crawler Box, F&R Lockers, 35" Centipedes, 4" lift. Overqualified WebWheeler!!!
Discovery - Bling touring stuff!
Discovery - Bling touring stuff!
TuffRR wrote:Bush65 wrote: I have the thermoguard kits for my 300TDi and 4BD1T diesels. They are pretty good IMHO. Especially for 300TDi discos - thermocouple mounts using EGR blanking plate and digital display fits neatly into disco dash.
Whereabouts have you mounted the display? I've had a quick look and no where obvious sticks out. It looks like it could be quite conspicuous and i dont want it distracting me at night.
Mine is in an early rangie, not so convenient.
Have a look here http://www.thermoguard.com.au/
John
Who is online
Users browsing this forum: Bing [Bot] and 2 guests