I need to offset the front radius arms on my disco. I have a 3" OME lift, 2' BL and 36" ET'II.
There is a lot of pressure on the bush and some driveline issues.
Need advise and drawing please showing how much to lenghten and to offset.
Thanks
Jay
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Off setting front radius arms
Moderator: Micka
Off setting front radius arms
96 Disco Gamel Trophy 36"*12.5 ET'II's, F&R ARB's,4.75 R&P GBR,GBR F&R
83 Rangie 2" OME Still Stock
83 Rangie 2" OME Still Stock
I drew mine on a peace of steel.
drew new hight of mount IE: lifted mount point 75mm
Bent arm to suit.
arm ended up 2mm shorter.
Michael.
drew new hight of mount IE: lifted mount point 75mm
Bent arm to suit.
arm ended up 2mm shorter.
Michael.
You do not have the required permissions to view the files attached to this post.
Mitsubishi 2010 NT DID Pajero wagon, Factory rear diff lock, Dual batteries, ARB bar, winch, Mt ATZ 4 rib tyres.
1986 RR.
Custom suspension links etc.
HSV 215 engine.
4.3 diffs.
1986 RR.
Custom suspension links etc.
HSV 215 engine.
4.3 diffs.
MichealHSV Rangie wrote:I drew mine on a peace of steel.
drew new hight of mount IE: lifted mount point 75mm
Bent arm to suit.
arm ended up 2mm shorter.
Michael.
Do you mean you lifted mount point 75 mm from center of radius arm?
On a 3" lift won't my arm be longer actually after bending?
Will it affect any driveline issues?
Did you work out from an actual radius arm....
Thanks
Jay
96 Disco Gamel Trophy 36"*12.5 ET'II's, F&R ARB's,4.75 R&P GBR,GBR F&R
83 Rangie 2" OME Still Stock
83 Rangie 2" OME Still Stock
Jay,
you may find issues with the uni's binding 75 mm is pushing the limit of front drive shaft
I run a high pinion front diff so I have no issues.
THe best way to fix the front suspension set up is IMO.
1: Bend ars so that the chassy bush is set as per std.
2: bend arm nearer to axle housing so that the pinion points at the out pout on the t/case.
3: Rotate swivell housings to correct castor.
This will se up the front so that it drives correctly.
Michael.
you may find issues with the uni's binding 75 mm is pushing the limit of front drive shaft
I run a high pinion front diff so I have no issues.
THe best way to fix the front suspension set up is IMO.
1: Bend ars so that the chassy bush is set as per std.
2: bend arm nearer to axle housing so that the pinion points at the out pout on the t/case.
3: Rotate swivell housings to correct castor.
This will se up the front so that it drives correctly.
Michael.
Mitsubishi 2010 NT DID Pajero wagon, Factory rear diff lock, Dual batteries, ARB bar, winch, Mt ATZ 4 rib tyres.
1986 RR.
Custom suspension links etc.
HSV 215 engine.
4.3 diffs.
1986 RR.
Custom suspension links etc.
HSV 215 engine.
4.3 diffs.
MichealHSV Rangie wrote:Jay,
you may find issues with the uni's binding 75 mm is pushing the limit of front drive shaft
I run a high pinion front diff so I have no issues.
THe best way to fix the front suspension set up is IMO.
1: Bend ars so that the chassy bush is set as per std.
2: bend arm nearer to axle housing so that the pinion points at the out pout on the t/case.
3: Rotate swivell housings to correct castor.
This will se up the front so that it drives correctly.
Michael.
I would appreciate if you can elborate more on point 2 and 3.
In case castor is not corrected ok i will be facing serious front vibes/driveline issues right?
Thanks
Jay
96 Disco Gamel Trophy 36"*12.5 ET'II's, F&R ARB's,4.75 R&P GBR,GBR F&R
83 Rangie 2" OME Still Stock
83 Rangie 2" OME Still Stock
Who is online
Users browsing this forum: No registered users and 0 guests