Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Pipe Bender ENERPAC

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 4275
Joined: Fri Nov 22, 2002 6:41 pm
Location: Western Australia

Pipe Bender ENERPAC

Post by Hoonz »

Any one had any experience with these?
its a bow and arrow styles bender?

pros?
cons?

anything?

http://www.enerpac.com/html/products/in ... 24e_Eg.pdf
H( * )( * )NZ loves B( * )( * )BIES
if a fat lady falls in the forest do the trees laugh?
[quote="RUFF"]although i didnt mean to, i squealed like a girl :armsup:[/quote]
Top
User avatar
Tiny
Road Ranger
Posts: 10722
Joined: Fri Nov 12, 2004 12:21 pm
Location: In a town near you

Contact:
Contact Tiny

Post by Tiny »

The only thing I could see being any issue would be how close you could get a bend to the edge so you may have a little more wastage on say sliders than using a draw through, and little bends close to eash other could prove difficult but they do with any thing and the hydaulic bit would be soooo much easier than using a ratchet lever type :armsup: feel like buying one for me to and sending it on down FOC
If the above post did not offend you in any way please PM me so I can try harder!!
Top
Posts: 4275
Joined: Fri Nov 22, 2002 6:41 pm
Location: Western Australia

Post by Hoonz »

should be ok ... we're actually getting the airoperated one so even easier
H( * )( * )NZ loves B( * )( * )BIES
if a fat lady falls in the forest do the trees laugh?
[quote="RUFF"]although i didnt mean to, i squealed like a girl :armsup:[/quote]
Top
Posts: 766
Joined: Sun Aug 01, 2004 7:16 pm
Location: brisbane

Post by bruiser »

what are these babys worth
Top
Posts: 4275
Joined: Fri Nov 22, 2002 6:41 pm
Location: Western Australia

Post by Hoonz »

i dunno RRP :twisted:
H( * )( * )NZ loves B( * )( * )BIES
if a fat lady falls in the forest do the trees laugh?
[quote="RUFF"]although i didnt mean to, i squealed like a girl :armsup:[/quote]
Top
Posts: 4225
Joined: Tue Jun 17, 2003 8:58 pm
Location: sunshine coast australia

Contact:
Contact mud4b

Post by mud4b »

the link is not working..
Mud4b/ OPT, Cheap rates, Not cheap work. Search Opt- option offroad on facebook. Call or Sms 0439609525.. Sunshine coast, Eudlo, 4554.
Top
Posts: 4275
Joined: Fri Nov 22, 2002 6:41 pm
Location: Western Australia

Post by Hoonz »

try and go to products then tools

http://www.enerpac.com
H( * )( * )NZ loves B( * )( * )BIES
if a fat lady falls in the forest do the trees laugh?
[quote="RUFF"]although i didnt mean to, i squealed like a girl :armsup:[/quote]
Top
User avatar
Tiny
Road Ranger
Posts: 10722
Joined: Fri Nov 12, 2004 12:21 pm
Location: In a town near you

Contact:
Contact Tiny

Post by Tiny »

mud4b wrote:the link is not working..
still works for me
If the above post did not offend you in any way please PM me so I can try harder!!
Top
Posts: 527
Joined: Sat Oct 02, 2004 3:55 pm
Location: Brisbane

Post by adam.s »

Hoonz wrote:i dunno RRP :twisted:
so approx. what are you paying ?

most people on here can get trade prices anyway, so it's no big secret ??
Top
Posts: 4275
Joined: Fri Nov 22, 2002 6:41 pm
Location: Western Australia

Post by Hoonz »

foad wrote:
Hoonz wrote:i dunno RRP :twisted:
so approx. what are you paying ?

most people on here can get trade prices anyway, so it's no big secret ??
well if u can get it then u can find out for yourself i have to keep it to myself
H( * )( * )NZ loves B( * )( * )BIES
if a fat lady falls in the forest do the trees laugh?
[quote="RUFF"]although i didnt mean to, i squealed like a girl :armsup:[/quote]
Top
Posts: 141
Joined: Fri Nov 12, 2004 4:46 pm
Location: Newcastle

Post by mickbeny »

Hi all...Worked with the exact one for donkeys years with the hand pump and the electric/hydrolic one,it also come with different size rams.good neat bends.I doubt it would be cheap though.
PEACE...
Top
Posts: 4275
Joined: Fri Nov 22, 2002 6:41 pm
Location: Western Australia

Post by Hoonz »

thats what i like to hear :armsup:
so with the electric hydraulic did it make the bending easy ... faster ?
we got the air/hydraulic one
H( * )( * )NZ loves B( * )( * )BIES
if a fat lady falls in the forest do the trees laugh?
[quote="RUFF"]although i didnt mean to, i squealed like a girl :armsup:[/quote]
Top
Posts: 1619
Joined: Wed Dec 24, 2003 11:26 pm
Location: Brisbane, Australia

Post by Rainbow Warrior »

Hoonz wrote:thats what i like to hear :armsup:
so with the electric hydraulic did it make the bending easy ... faster ?
we got the air/hydraulic one
I usually found in cage making comps a faster tape measure & drop saw is more important than the bender, a suitable modified 50tonne hydraulic press is the go :D :roll:
Pat,
Brisbane, Australia,
JK 4door Rubicon, currently 4 Sale :(
It's a Jeep thing, I don't understand........
Top
Posts: 928
Joined: Tue Apr 06, 2004 5:42 pm
Location: newy

Post by customhilux »

dude if ya got the money for it, go for it

enerpac make a good pneumatic pump,

they have a little pneumatic piston pump inside them, if ya want more power out of it, rip the lid off the tank and screw the relief sticking out, but get yaself a pressure gauge, so you'll know what pressure u have(the pump and cylinder are good for 10,000psi), but the bender wont handle that.

but the good thing is, if ya need to straighten something as well, use the cylinder and pump,


also let us know what price u can get it for, i'd like to compare it, we sell enerpac gear. :lol:
[url=http://www.outerlimits4x4.com/PHP_Modules/phpBB2/viewtopic.php?t=47136]THE SUSLUX[/url]
[url=http://www.outerlimits4x4.com/PHP_Modules/phpBB2/viewtopic.php?t=50913]THE EXTRACAB[/url]
Top
Posts: 3739
Joined: Sat Dec 11, 2004 10:10 pm

Post by mickyd555 »

im looking at the one that trade tools sell, its only a bit over $300 but apparently plumbers love them. just not sure whether it comes with metric dies for it. It looks to be the same sort of setup as that one, but with a lever for the bottle jack type setup............
Top
Posts: 2853
Joined: Tue Nov 30, 2004 10:55 pm
Location: All over the world or your mum

Post by toughnut »

Hey Hoonz that's the one that I used to make all the bar work for my truck. Using the hand pump made it more acurate and taking it slow made for a better bend. I can get hold of it again so you can have a look if you like. :D
j-top paj wrote:gayer than jizz on a beard
http://www.outerlimits4x4.com/viewtopic ... 6&t=231346
Top
Posts: 826
Joined: Sat Mar 13, 2004 4:18 pm
Location: Northern NSW

Post by slosh »

I'm about to buy a bender but was leaning toward the speedwerx one- totally different beast that manufacturer claims will distort less than anything this side of a mandrel bender.
However it would be nice to hear how well these work they look to be good quality.
A basic speedwerx is $760 or so for the bender, $1050 ish for air/ hydraulic, and the dies vary in price from $300ish for a littly, to $680 for 2". These are retail prices- if anyone could get me a trade discount it would be nice!
Top
Posts: 2853
Joined: Tue Nov 30, 2004 10:55 pm
Location: All over the world or your mum

Post by toughnut »

This is the best pic of the bends on my tray at the moment. I'll try to get a better pic soon.
Image
j-top paj wrote:gayer than jizz on a beard
http://www.outerlimits4x4.com/viewtopic ... 6&t=231346
Top
Posts: 4583
Joined: Fri Jun 11, 2004 5:57 pm
Location: Wheeling in my backyard

Post by sierrajim »

I think that Gwagensteve has a speedworks one. I've seen soem of the work he's done with it and it seems to be very good. Tube distorsion is minimal.
[quote="Harb"]Well I'm guessing that they didn't think everyone would carry on like a big bunch of sooky girls over it like they have........[/quote]
Top
Posts: 130
Joined: Mon Jun 30, 2003 12:44 pm
Location: Melbourne

Enerpac bender

Post by davejb »

An alternative for the guys with a limited budjet.
Buy an elcheepo bender and the buy the enerpac formers to suit the size pipe you want to bend. The enerpac formers are proberly the best you can get for bending pipe (not DOM tube)
All you need to do is make a bush to fit between the the ram and former

Dave
Top
Posts: 1889
Joined: Mon Sep 20, 2004 10:23 pm
Location: Brisbane

Post by just cruizin' »

C'mon guys what sort of $$ are we talking about? OK most of us get trade but we know what % we get so we can work out what it'll cost us. It'll just save a lot of wasted phone calls.
Top
Posts: 141
Joined: Fri Nov 12, 2004 4:46 pm
Location: Newcastle

Post by mickbeny »

Hi all...Hoonz,put it this way,you dont sweat with the power operated.LOL.Its no more or less accurate than the hand pump.
PEACE...
Top
Posts: 4275
Joined: Fri Nov 22, 2002 6:41 pm
Location: Western Australia

Post by Hoonz »

customhilux deals enerpac gear, im pretty sure he'll post up a price
later on tonite ...
H( * )( * )NZ loves B( * )( * )BIES
if a fat lady falls in the forest do the trees laugh?
[quote="RUFF"]although i didnt mean to, i squealed like a girl :armsup:[/quote]
Top
Posts: 1889
Joined: Mon Sep 20, 2004 10:23 pm
Location: Brisbane

Post by just cruizin' »

Right you lazy buggers, I've made the call.

Enerpak pipe bender $3833 + GST trade
Top
Posts: 4275
Joined: Fri Nov 22, 2002 6:41 pm
Location: Western Australia

Post by Hoonz »

what does that include just cruizin?
H( * )( * )NZ loves B( * )( * )BIES
if a fat lady falls in the forest do the trees laugh?
[quote="RUFF"]although i didnt mean to, i squealed like a girl :armsup:[/quote]
Top
Posts: 1619
Joined: Wed Dec 24, 2003 11:26 pm
Location: Brisbane, Australia

Post by Rainbow Warrior »

Hoonz wrote:what does that include just cruizin?
Because we're not telling anybody anything, I'm not telling where you can get a basic footpedal air/pnemautic pump for $600 and a forward/reversable one for $1200
Pat,
Brisbane, Australia,
JK 4door Rubicon, currently 4 Sale :(
It's a Jeep thing, I don't understand........
Top
Posts: 3739
Joined: Sat Dec 11, 2004 10:10 pm

Post by mickyd555 »

ok, all this talk about tube benders...........the one that i was refering to from QLD trade tools. is it just a waste of time, or is it just gonna be harder to use?? its only $300 odd dollars, but i dont wana waste $300 if its useless. id rather save up and spend a few more bucks, but i dont think id spend $3000................. :shock:
Top
Posts: 4275
Joined: Fri Nov 22, 2002 6:41 pm
Location: Western Australia

Post by Hoonz »

hahaha *points and laughs*
H( * )( * )NZ loves B( * )( * )BIES
if a fat lady falls in the forest do the trees laugh?
[quote="RUFF"]although i didnt mean to, i squealed like a girl :armsup:[/quote]
Top
Posts: 4275
Joined: Fri Nov 22, 2002 6:41 pm
Location: Western Australia

Post by Hoonz »

just cruizin' wrote:Right you lazy buggers, I've made the call.

Enerpak pipe bender $3833 + GST trade

there you go theres the price for the enerpac bender 3833+ GST trade :rofl: :armsup:
H( * )( * )NZ loves B( * )( * )BIES
if a fat lady falls in the forest do the trees laugh?
[quote="RUFF"]although i didnt mean to, i squealed like a girl :armsup:[/quote]
Top
Posts: 3739
Joined: Sat Dec 11, 2004 10:10 pm

Post by mickyd555 »

Hoonz wrote:
just cruizin' wrote:Right you lazy buggers, I've made the call.

Enerpak pipe bender $3833 + GST trade

there you go theres the price for the enerpac bender 3833+ GST trade :rofl: :armsup:
and hoonz's price is <insert price here>

and then onsell to us poor buggers.(unless its more than $300, then i dont want it............... :lol: :lol: )
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 113 guests