Thinking about doing 33" on Rangie 83 (LT 95 and 4 gears/ 3.5 L carburator)
Will I need to adjust the gearing 4.11 CR&P
Truck will be used for mild off-roading
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
LT 95 gearing with 33"
Moderator: Micka
LT 95 gearing with 33"
96 Disco Gamel Trophy 36"*12.5 ET'II's, F&R ARB's,4.75 R&P GBR,GBR F&R
83 Rangie 2" OME Still Stock
83 Rangie 2" OME Still Stock
Bolt them on and see what you think will slow you down on road but not so much off road better of upgrading 3.5 than changing ring and pinion ha ha iknow plenty of people running 3.54 gearing and 35's with no drama's gearing wise but they all ahave larger motors.
Wanted: Car trailer or beaver tail truck, let me know what you got
LT 95 gearing with 33"
Depeding on the high range gears that you have.
Its possible to swap them, they range from .99621 to 1.127 to 1.
If you had the .99621 set (can check by gearbox no.) the 1.127 would make it more drivable for less dollars than 2 cw+p's or larger motor.
It can be done insitu but its quite fidly even on the bench.
The gear sets should cost around $200.
I have just done this mod, got further info if you need it.
Michael.
Its possible to swap them, they range from .99621 to 1.127 to 1.
If you had the .99621 set (can check by gearbox no.) the 1.127 would make it more drivable for less dollars than 2 cw+p's or larger motor.
It can be done insitu but its quite fidly even on the bench.
The gear sets should cost around $200.
I have just done this mod, got further info if you need it.
Michael.
out of my mind, back soon.
Re: LT 95 gearing with 33"
Michealswamp wrote:Depeding on the high range gears that you have.
Its possible to swap them, they range from .99621 to 1.127 to 1.
If you had the .99621 set (can check by gearbox no.) the 1.127 would make it more drivable for less dollars than 2 cw+p's or larger motor.
It can be done insitu but its quite fidly even on the bench.
The gear sets should cost around $200.
I have just done this mod, got further info if you need it.
Michael.
Thanks for the feedback. Are you running an LT 95?
The truck has 32" ET II now got them off my disco it has slown down just a bit but still driveable.
The 32" have slowed down the Disco more even tough it has a 3.9L injection.
I guess the LT 95 makes all the difference on the rangie(3.5L carburator)
Micheal where can I check these numbers ??
thanks
96 Disco Gamel Trophy 36"*12.5 ET'II's, F&R ARB's,4.75 R&P GBR,GBR F&R
83 Rangie 2" OME Still Stock
83 Rangie 2" OME Still Stock
LT 95 gearing with 33"
As per workshop manual
On the rear of the transfer case just below and to the side of the filler plug
is the suffix number
Suffix A + B - 1.174:1
Suffix C -1.113:1
Suffix C from gearbox No.35594060 C - 1.123:1
Prefix 12C -0.996:1
If you think you can gain enough spread , as I said previously
.99621 to 1.174 would be a worthwhile gain. You can confirm the high range gearing by doing a tooth count on the high range (big) gear on the intermediate shaft (I have the numbers somewhere).
I have just rebuilt and installed an LT95.
Getting the intermediate gears into the gear box was a pain in the arse
but after a while I got the knack of it.(I did it on the bench)
If your not really familiar with gearboxes it may be worth it to farm it out to someone with experience in LR gearboxes.
Post up if you need more.
Michael
On the rear of the transfer case just below and to the side of the filler plug
is the suffix number
Suffix A + B - 1.174:1
Suffix C -1.113:1
Suffix C from gearbox No.35594060 C - 1.123:1
Prefix 12C -0.996:1
If you think you can gain enough spread , as I said previously
.99621 to 1.174 would be a worthwhile gain. You can confirm the high range gearing by doing a tooth count on the high range (big) gear on the intermediate shaft (I have the numbers somewhere).
I have just rebuilt and installed an LT95.
Getting the intermediate gears into the gear box was a pain in the arse
but after a while I got the knack of it.(I did it on the bench)
If your not really familiar with gearboxes it may be worth it to farm it out to someone with experience in LR gearboxes.
Post up if you need more.
Michael
out of my mind, back soon.
Who is online
Users browsing this forum: No registered users and 0 guests