Hi guys, I thought I'd share a little of what I did this weekend.
Maybe someone in the same financial constraints may benefit from it.
My Toyota Blizzard rear right 3rd leaf had snapped, (I bought it that way), and driving on uneven road surfaces would feel really dangerous if I was doing 100km/hr. Also my kidneys bounce from my ars*e to my neck on rough terrain.
I searched the wreckers with no luck, and run up Toyota, $1200 per side! Bugger that!
So I measured up the leaves and went to a wrecker to find something similar.
Long story short, I ended up all weekend putting in leafs from a Mazda/Ford Econovan. Drives sh*tloads better and no dangerous wobble.
Cost $24.00 for the pair, and some skin off the left knuckle.
Oh well, as my old man use to say, flesh can heal, cars don't.
I haven't gone off road yet, so we'll see.
With the new leafs, it sits higher at the rear, so I'll have to look for some front leafs too.
Anyone got a tip for which may fit the front?
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Cheap Leaf Spring alternative
Moderator: Tiny
Just an update.
After driving around for a week, and checking out the articulation, I noticed it didn't have much.
So I've removed one of the lower leafs.
The rides doesn't seem to have changed much, but now it's even higher than before, (about another inch).
It's looking slightly strange now with the front noticeably lower than the rear.
The rear wheel arch space, you could play cricket in. (I've only got 235x15s).
I'm gonna have to raise the front, so as per previous post, anyone got a very cheap tip for the front leaf sprung rigid axle?
I thought of transplanting the rear coils off a hiace Custom van.
And keep the leafs on, i.e. no requirement for additional stabliser arms etc.
I'm not sure if articultion/ride is affect with this type of setup though.
After driving around for a week, and checking out the articulation, I noticed it didn't have much.
So I've removed one of the lower leafs.
The rides doesn't seem to have changed much, but now it's even higher than before, (about another inch).
It's looking slightly strange now with the front noticeably lower than the rear.
The rear wheel arch space, you could play cricket in. (I've only got 235x15s).
I'm gonna have to raise the front, so as per previous post, anyone got a very cheap tip for the front leaf sprung rigid axle?
I thought of transplanting the rear coils off a hiace Custom van.
And keep the leafs on, i.e. no requirement for additional stabliser arms etc.
I'm not sure if articultion/ride is affect with this type of setup though.
Depends on how much it has to be raised. Legalities aside, easiest way is longer shackles.
You could use (part of) the original rear spring pack up front. The main leaf is about 10 cm longer, so have them reset at the same height as the rear springs. Do some measurements if this will fit with the stock shackles and fixed springhanger and if needed correct this.
Just keep us posted if you find other leafs which are 6 cm wide
You could use (part of) the original rear spring pack up front. The main leaf is about 10 cm longer, so have them reset at the same height as the rear springs. Do some measurements if this will fit with the stock shackles and fixed springhanger and if needed correct this.
Just keep us posted if you find other leafs which are 6 cm wide
smokin' is bad, especially for your curtains
----------------------------------------------------------
F20 Resin Top, 2.5" lift , 31" Grabber AT's
----------------------------------------------------------
F20 Resin Top, 2.5" lift , 31" Grabber AT's
shackle lifts on the front are a BAD idea if you go more than about an inch (one inch longer shackles only give 1/2 an inch lift too)... they mess up castor and your handlingelgordomuygrande wrote:Depends on how much it has to be raised. Legalities aside, easiest way is longer shackles.
You could use (part of) the original rear spring pack up front. The main leaf is about 10 cm longer, so have them reset at the same height as the rear springs. Do some measurements if this will fit with the stock shackles and fixed springhanger and if needed correct this.
Just keep us posted if you find other leafs which are 6 cm wide
you can get your front leafs reset to match the height of the rear, a place i went to in melbourne did a hot reset (alot less likely to sag) for 70 bucks a side... that included a new main leaf made up longer to keep the shackle angle the same
the same place did a 75 series ute 3 years ago and it still hasn't sagged more than 1/4 an inch
Spit my last breath
just an update on my continual search for free or almost free stuff.
My shocks are pretty much knackered and a friend offered his factory hilux ones, (also electric adjustable), as he got old man emu ones.
problem is that the hilux ones, though being larger in diameter, and has an extra couple of inches more travel, have larger bottom mounts and the tops don't fit properly.
anyway, I managed to modify the hilux rear shocks slightly and have got them working on my blizzard. just needed larger bushes on the bottom, and hack sawed a little bit away on the top to fit the electric motors.
oh most of you probably already know, when taking the electric motors on/off you will also require several words regarding intercourse. whoever designed the dam top mounting must have been senile
My shocks are pretty much knackered and a friend offered his factory hilux ones, (also electric adjustable), as he got old man emu ones.
problem is that the hilux ones, though being larger in diameter, and has an extra couple of inches more travel, have larger bottom mounts and the tops don't fit properly.
anyway, I managed to modify the hilux rear shocks slightly and have got them working on my blizzard. just needed larger bushes on the bottom, and hack sawed a little bit away on the top to fit the electric motors.
oh most of you probably already know, when taking the electric motors on/off you will also require several words regarding intercourse. whoever designed the dam top mounting must have been senile
Who is online
Users browsing this forum: No registered users and 0 guests