People!
After reading several threads about failed rear rover ring & pinion (on MANY forums...), I have decided to swap in a disc-braked Salisbury with my matching front 4.7 ratio. Kindly bear with me as I think this through, and PLEASE shed as much light as possible:
1. The rear axle has been relocated 2cm to the rear with modified rear lower links, and the truck sits on 2" OME lift (with a 2" Body lift). WILL THIS ALLOW THE BIG SALISBURY TO FIT THE REAR DRIVE SHAFT AND CLEAR THE REAR FUEL TANK?
2. The Rover R&P is ~8" in diameter, and even with the super duper metal and 600US$ 4.75s, you can still break them...WHAT IS THE R&P DIAMETER OF THE SALISBURY R&P?
3. WILL THE STOCK SALISBURY 4.7 RATIO HOLD TO <37" TIRES?
4. I need discs alround, therefore, IF I FIND A DRUM VERSION, CAN I CHANGE THE FINAL HUB ASSEMBLY WITH THE NEWER DISC VERSION?
That is all I have for the moment...I wish I had another choice for keeping my Rover axle for the greater clearence, but we do not have Toyota parts here, and Land Rover parts are all over the place and cost piss. This IS the only way...Please advise.
Thanks guys...
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Slapping a rear Salisbury in a Discovery
Moderator: Micka
Slapping a rear Salisbury in a Discovery
LR Disco truggy:
42" Iroks, ZF, dual cases & ARBs, 30 splined, Longfielded, OMEs, Optimas, M8274-50s, Rockstomper rope & Bead-L
LR D-90 TD5 ST:
33" BFT AT, tuned, caged, 1/2 top
42" Iroks, ZF, dual cases & ARBs, 30 splined, Longfielded, OMEs, Optimas, M8274-50s, Rockstomper rope & Bead-L
LR D-90 TD5 ST:
33" BFT AT, tuned, caged, 1/2 top
1. probably not,but I'm guessing
2. bigger than 8", around 9", less than 10"
3. yes, but the axles wont
4. search on pirate, this has been covered recently
not very helpful, but a start
just put toy gears in and be done, either toy thirds or on your MD hemi. better clearance and will survive 37's fine, and cheaper.
Cheers
Daryl
2. bigger than 8", around 9", less than 10"
3. yes, but the axles wont
4. search on pirate, this has been covered recently
not very helpful, but a start
just put toy gears in and be done, either toy thirds or on your MD hemi. better clearance and will survive 37's fine, and cheaper.
Cheers
Daryl
THe pirate thread>
http://www.pirate4x4.com/forum/showthre ... did=141673
But I would go the Toy diff centres. And I have.
Been down this exercise.
Michael.
http://www.pirate4x4.com/forum/showthre ... did=141673
But I would go the Toy diff centres. And I have.
Been down this exercise.
Michael.
Mitsubishi 2010 NT DID Pajero wagon, Factory rear diff lock, Dual batteries, ARB bar, winch, Mt ATZ 4 rib tyres.
1986 RR.
Custom suspension links etc.
HSV 215 engine.
4.3 diffs.
1986 RR.
Custom suspension links etc.
HSV 215 engine.
4.3 diffs.
I have put a salsbury into the rear of my disco. A couple of things were required.
1) adaptor plates for the disc brakes and discovery outers to fit on
2) modified fuel tank in my case due to the diff hitting the tank
( note I have extend trailing arms so this was an issue)
I run a maxi drive in the rear and maxidrive made the adaptor plates plus the axles. For my particular model the axles were 20mm longer than the normal ones supplied due to the early model disco outers.
I run a modified 4.6lt and drive like a lunatic currently with 35" MTRS. I have had simex etc and never had a problem with the diff.
The old rover diff even with 4.11s used to break the cw& p all the time.
I got sick of it and went straight to salsbury. The only issue now is ground clearance under the diff so Im going to 36" centerpedes Hopefully
1) adaptor plates for the disc brakes and discovery outers to fit on
2) modified fuel tank in my case due to the diff hitting the tank
( note I have extend trailing arms so this was an issue)
I run a maxi drive in the rear and maxidrive made the adaptor plates plus the axles. For my particular model the axles were 20mm longer than the normal ones supplied due to the early model disco outers.
I run a modified 4.6lt and drive like a lunatic currently with 35" MTRS. I have had simex etc and never had a problem with the diff.
The old rover diff even with 4.11s used to break the cw& p all the time.
I got sick of it and went straight to salsbury. The only issue now is ground clearance under the diff so Im going to 36" centerpedes Hopefully
You three were on the top of my head when it came to answering this thread, and you guys ulled through beautifully! 
Anyways, I know the topic was on pirates, but in the US, the salisbury is not a cost effective choice. In Aust., it is more of a smart one, other than the best which is the Toy centers. Again, I insist on saying that unfortunately, I cannot go with Toys since they are NOT available here, and a Salisbury is easier to get. Plus keeping everything LR is kinda sweet (yet foolish ).
Daryl, I'll be slapping in the ARB locker into it, and the MD disc brake version HD axles.
So Discokid...where do I get these adapters for the Disco outers? Can I do without them and just use the D110 Disc outers? my rear lower links are extended 2cm, but the top "Y" is not, will that save me cutting the tank? What about the drive-shaft? is taht safe? Preach oh wise one!
Anyways, I know the topic was on pirates, but in the US, the salisbury is not a cost effective choice. In Aust., it is more of a smart one, other than the best which is the Toy centers. Again, I insist on saying that unfortunately, I cannot go with Toys since they are NOT available here, and a Salisbury is easier to get. Plus keeping everything LR is kinda sweet (yet foolish
).
Daryl, I'll be slapping in the ARB locker into it, and the MD disc brake version HD axles.
So Discokid...where do I get these adapters for the Disco outers? Can I do without them and just use the D110 Disc outers? my rear lower links are extended 2cm, but the top "Y" is not, will that save me cutting the tank? What about the drive-shaft? is taht safe? Preach oh wise one!
LR Disco truggy:
42" Iroks, ZF, dual cases & ARBs, 30 splined, Longfielded, OMEs, Optimas, M8274-50s, Rockstomper rope & Bead-L
LR D-90 TD5 ST:
33" BFT AT, tuned, caged, 1/2 top
42" Iroks, ZF, dual cases & ARBs, 30 splined, Longfielded, OMEs, Optimas, M8274-50s, Rockstomper rope & Bead-L
LR D-90 TD5 ST:
33" BFT AT, tuned, caged, 1/2 top
The adaptors came from Maxidrive in Queensland. I had a local supplier here source them for me. As I said my disco is an early model so Im not sure that they are all the same ( i originally had 10 spline axles).
My driveshaft was modified at the same time. However they put a Hilux cardin joint in I think mine came back to standard length with 5" suspension lift. It was actually to short with the old rover diff.
I have slightly longer trailing arms as well but havent done anything with the top. The rear of the salsbury only just nicked the tank so there may be a bit of trial and error unless someone else is wiser.
I would contact maxidrive and see if you can get the plates. They allow for the brake caliper to go back in original position etc so it really was a straight bolt up up job.
My driveshaft was modified at the same time. However they put a Hilux cardin joint in I think mine came back to standard length with 5" suspension lift. It was actually to short with the old rover diff.
I have slightly longer trailing arms as well but havent done anything with the top. The rear of the salsbury only just nicked the tank so there may be a bit of trial and error unless someone else is wiser.
I would contact maxidrive and see if you can get the plates. They allow for the brake caliper to go back in original position etc so it really was a straight bolt up up job.
Who is online
Users browsing this forum: No registered users and 38 guests