Hey people, I have a 2L sigma engine in my project car and on the way home from my last trip I noticed the oil pressure guage shows no pressure, I checked the dipstick and its showing oil so was wondering how to figure out if its just the wires in the dash or perhaps the oil pump has blown.. any suggestions?
Cheers
Paul
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
oil pressure guage showing nothing.. plz help..
Moderators: toaddog, TWISTY, V8Patrol, Moderators
a oil sender
b gauge
c no oil presure
d wiring
is it nocking/ratteling?
1 park on grass or road or next door nebours yard.
2 pull oil prsure sender out
3 turn motor over a few times (switch off it motor starts)
4 check... there will be oil everywhere (should b)
5 steem clean engen/every thing that is coerd in oil
6 replace oil cender.
actualy set up a vid camera so we can watch the mess unfold
Phil
b gauge
c no oil presure
d wiring
is it nocking/ratteling?
1 park on grass or road or next door nebours yard.
2 pull oil prsure sender out
3 turn motor over a few times (switch off it motor starts)
4 check... there will be oil everywhere (should b)
5 steem clean engen/every thing that is coerd in oil
6 replace oil cender.
actualy set up a vid camera so we can watch the mess unfold
Phil
You can either do what was suggested above 
but you really should check oil pressure with an oil pressure gauge 
.
If its very rattly its fair to assume there is no oil pressure.
Things to look for, blocked oil pickup (common if there has been few oil chaneges), faulty oil pump, sludging of the oil galleries & if it is an Astron engine the oil pump is driven by the balance shaft chain which has a habit of breaking if not adjusted frequently.
Either way you will have to do a major strip to find the problem.
If it has oil pressure then the problem will be with the gauge or what operates it.
but you really should check oil pressure with an oil pressure gauge .If its very rattly its fair to assume there is no oil pressure.
Things to look for, blocked oil pickup (common if there has been few oil chaneges), faulty oil pump, sludging of the oil galleries & if it is an Astron engine the oil pump is driven by the balance shaft chain which has a habit of breaking if not adjusted frequently.
Either way you will have to do a major strip to find the problem.
If it has oil pressure then the problem will be with the gauge or what operates it.
Don't ask me, ask them. I'm just runnin for my life myself.
Well they are all following you...
No they ain't, I'm just in front...............
Well they are all following you...
No they ain't, I'm just in front...............
it could be simple as. u probably have a mech pressure gauge, which just has a clear line coming from the gauge in to the eng block, that way it rules out any electrical fault or sender prob, check the line if its clear when eng is running, it should have solid oil content as to tell u that its sealed and sending full correct pressure to gauge, ne air pockets could indicate leak in line or fittings which may be whats causing faulty gauge reading.
hope u got a mech gauge cause a new one cost $20 and consists of a gauge a line n no rocket science to fit. hope this helps
hope u got a mech gauge cause a new one cost $20 and consists of a gauge a line n no rocket science to fit. hope this helps
Who is online
Users browsing this forum: No registered users and 1 guest