Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Sheered Wheel Bolt

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 191
Joined: Mon Nov 29, 2004 5:42 pm
Location: melbourne

Sheered Wheel Bolt

Post by kranked_dirt »

G'day guys, while trying to remove the wheel nuts on the fourby i just sheered one of the bolts (/pins?) right off. Can the individual bolts be replaced or am i up for a new front hub? It is an FJ40 with front discs, i need the quickest cheapest fix as i am going away tomorrow. Or will it be okay missing just one nut till i get back??

Cheers,

Adam
went there dressed up, came back messed up

81 FJ40 hardtop - Lexus 1UZ-FE conversion underway
Top
Posts: 2492
Joined: Sun Nov 24, 2002 8:57 pm
Location: Melbourne

Post by bazzle »

Fix it. Other ones may be weak and could fail on you with inc loads.
Drive old one out, pull new one in with wheel nut and lube. Check it a few times as it seats for a couple of days.
Most auto spares places and dealers keep studs.

Bazzle
Top
Posts: 5179
Joined: Fri Dec 05, 2003 8:15 pm
Location: Brisbane Australia

Post by Shadow »

yep you can replace the studs.

Ass bazzle suggested its probably worthwhile replacing all of them. If one of them sheared it would be safe to assume the others have been stressed or rusted as much as it was.
Top
Posts: 6221
Joined: Tue May 31, 2005 12:51 pm
Location: Sydney

Post by v840 »

If it becomes a common problem you could also consider drilling and tapping the hubs to accept 100 series studs (10mm) which are heaps stronger than the 40/60/80 ones (8mm). Definitely fix it though.
|^^^^^^^^^^^^^^| ||
|.........SUZUKI..........| ||'|";, ____.
|_..._..._______===|=||_|__|..., ]
(@)'(@)"""''"**|(@)(@)*****''(@)
Top
Posts: 5179
Joined: Fri Dec 05, 2003 8:15 pm
Location: Brisbane Australia

Post by Shadow »

v840 wrote:If it becomes a common problem you could also consider drilling and tapping the hubs to accept 100 series studs (10mm) which are heaps stronger than the 40/60/80 ones (8mm). Definitely fix it though.
fairly sure he means wheel studs, not axle studs.
Top
Posts: 2384
Joined: Mon Mar 31, 2003 10:05 am
Location: Brisbane or 169.254.243.241

Post by RaginRover »

Don't know how the tojo hubs work but always take care when you separate the hub from the brake disc that you don't destroy the bearing

Tom
Top
Posts: 268
Joined: Tue Apr 19, 2005 7:00 pm
Location: Brisbane

Post by Rangie ute on 38'' »

youll be right with 5, but get one asap, weve mustered out at ethel crk in a 40 with 3 studs on a front hub :lol!:
Top
Posts: 191
Joined: Mon Nov 29, 2004 5:42 pm
Location: melbourne

Post by kranked_dirt »

Thanks for the replys guys, i ended up taking it into a 4x4 service center to get done (wont mention which one) as i didnt have time to do it myself as i was headed up to the snow the next morning. Ended up costing me 92 ****ing dollars AND on the way up the hume hwy just out of glenrowen i had to pull over as there was a violent shudder going through the steering. Got out and had a look and the stud they replaced had snapped, two wheel nuts missing (including one lock nut) and the remaining three were half undone! I thought they used rattle guns in these places, how the hell could they come undone like that on the hwy travelling at 90km/h???
went there dressed up, came back messed up

81 FJ40 hardtop - Lexus 1UZ-FE conversion underway
Top
Posts: 1552
Joined: Wed Dec 22, 2004 12:09 pm
Location: im at wello point

Post by bilby »

or get used to dealing with this look :D :finger:
http://www.outerlimits4x4.com/PHP_Modul ... hp?t=55765
just a little left of insanity :)
Top
Posts: 5179
Joined: Fri Dec 05, 2003 8:15 pm
Location: Brisbane Australia

Post by Shadow »

kranked_dirt wrote:Thanks for the replys guys, i ended up taking it into a 4x4 service center to get done (wont mention which one) as i didnt have time to do it myself as i was headed up to the snow the next morning. Ended up costing me 92 ****ing dollars AND on the way up the hume hwy just out of glenrowen i had to pull over as there was a violent shudder going through the steering. Got out and had a look and the stud they replaced had snapped, two wheel nuts missing (including one lock nut) and the remaining three were half undone! I thought they used rattle guns in these places, how the hell could they come undone like that on the hwy travelling at 90km/h???
well they obviously forgot to tighten them so they are dicks.

If the same stud that snapped before broke again id be curious as to the strength of the stud they replaced it with. Really the new stud should be stronger than any of the old(er) ones.

Id probably go back and ask fur a full refund and the work to be corrected. If they dont do that id tell everyone i could how much of a bunch of dicks they are!.
Top
Posts: 6221
Joined: Tue May 31, 2005 12:51 pm
Location: Sydney

Post by v840 »

fairly sure he means wheel studs, not axle studs.
Sorry, I misread the original post. :oops: :finger:
|^^^^^^^^^^^^^^| ||
|.........SUZUKI..........| ||'|";, ____.
|_..._..._______===|=||_|__|..., ]
(@)'(@)"""''"**|(@)(@)*****''(@)
Top
Posts: 191
Joined: Mon Nov 29, 2004 5:42 pm
Location: melbourne

Post by kranked_dirt »

G'day all, well i took it back yesterday and picked it up today. They ended up replacing all the wheel studs free of charge, which i thought was the least they could have done. Im just glad its out of the way now. The service manager was VERY apologetic as well which is always good to see.
went there dressed up, came back messed up

81 FJ40 hardtop - Lexus 1UZ-FE conversion underway
Top
Posts: 283
Joined: Fri May 20, 2005 1:55 pm
Location: maitland

Post by matto »

some repairers are pathetic my mate went in for new tyres and they let him drive out with the wheel nuts finger tight, he went off his nut (red head)and didnt pay all the price.
I recently replaced my wheel studs, easy job and the cost was around $2.20 each. thats on a gq though. :cool:
nissan 98 gu 5" lift 37 creepys, 80%reduction gears, front locker and a gen3 and no money.
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 3 guests