had some electrical issues after visiting ormeau tonight.. like no electrics at all, no acc, no glow, no start. nothing.
so we are at the water tower (good place for a hill start) and we'd try and get my 3b started.
in 2nd, 2wd, clutch in, key to on, rolling down the hill and take the clutch out.. it sounds like the engine starts or is running but there is no accelerator.
you could hear the engine running (compression?) but when you didnt have the momentum and put the clutch in it would stall and stop.
anyway.. we diagnosed the problem to some a dodgy heavy cable to the alt and a fried fusable link..
but the question is why could i not accelerate after i had compression.
I thought the 3b was mostly mechancial (fuel pump? ).. I realise the edic motor is required to overfuel for starting would not work without power, but is this still required when hill starting? would you have to engage the edic motor manually while your rolling down the hill.
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
hill starting a diesel with no elecrtics
Moderators: toaddog, TWISTY, V8Patrol, Moderators
does it have an EDIC?InSanE wrote:the motor should have different settings for start, run and stop so i guess you might have to manually put it to run for it to work properly (just a guess)
in any case it has to have some sort of shutoff for the diesel pump, you need to pull this to the run position as InSanE said.
With an Edic the easiest way is to drop the shaft off the edic motor and push the rod forward (toward radiator). From memory it should stay in the run position, but you may need to wire it there or something.
Most diesels have an electric solenid on the pump that turns the fuel off when it doesn't have power. If you want to start it you need to supply power to the solenoid.
It is often possible (but illegal on post 79? diesels) to put a mechanical cable (e.g. choke cable) instead of the solenoid - this gives you purely machanical operation and it will start fine without any electrics.
It is often possible (but illegal on post 79? diesels) to put a mechanical cable (e.g. choke cable) instead of the solenoid - this gives you purely machanical operation and it will start fine without any electrics.
_____________________________________________________________
RUFF wrote:Beally STFU Your becoming a real PITA.
My first car was a 76 landcruiser shorty and the only way you could stop was by pulling the cable in the dash.
I could clutch start the car no worries even without a battery in the car.
I broke the cable once as well. I had to stall the car anytime I wanted to turn it off for about 6 months.
I would most likely still have that car rustung in the back yard if my brother hadn't rolled it.
I could clutch start the car no worries even without a battery in the car.
I broke the cable once as well. I had to stall the car anytime I wanted to turn it off for about 6 months.
I would most likely still have that car rustung in the back yard if my brother hadn't rolled it.
My Cruiser is Environmentally Friendly.
It runs on recycled Dinosaurs.
It runs on recycled Dinosaurs.
close. the 'run' position of the EDIC is back, but not all the way back - right back is overinject (start) and forward is shutoff. just pop the pushrod off and a cable tie or something will hold it in position - it will probably default to a run position but could flop foward to stopShadow wrote:does it have an EDIC?InSanE wrote:the motor should have different settings for start, run and stop so i guess you might have to manually put it to run for it to work properly (just a guess)
in any case it has to have some sort of shutoff for the diesel pump, you need to pull this to the run position as InSanE said.
With an Edic the easiest way is to drop the shaft off the edic motor and push the rod forward (toward radiator). From memory it should stay in the run position, but you may need to wire it there or something.
Free air locker to the first 20 callers!
I had one of the fuseable links go on me one night 
it was raining and i first noticed it when i was slowing down for a corner clutch in and the elec's turned off then the motor died!! I was probablly doing 15km and released the clutch in second and it all started again. After i stoped it wouldn't start and I ended up using a piece of solid wire to bridge the link. when i was driving it to the servo the volt meter was reading 16v when i was accelerating!! i was able to role alot of the way there luckly beacuse when i pushed the clutch in the volts dropped. The servo had some fuse wire so i was able to fix it and get home 
it was raining and i first noticed it when i was slowing down for a corner clutch in and the elec's turned off then the motor died!! I was probablly doing 15km and released the clutch in second and it all started again. After i stoped it wouldn't start and I ended up using a piece of solid wire to bridge the link. when i was driving it to the servo the volt meter was reading 16v when i was accelerating!! i was able to role alot of the way there luckly beacuse when i pushed the clutch in the volts dropped. The servo had some fuse wire so i was able to fix it and get home HJ60 Cruiser, headers and exhust, 4 spd.
96 DX Cruiser, Diesel, 2' lift, Snorkel +More
96 DX Cruiser, Diesel, 2' lift, Snorkel +More
Who is online
Users browsing this forum: No registered users and 26 guests