80 series eng fan cfm?

Post by **RV80** » Wed Jan 04, 2006 3:41 pm

I'm looking at pulling out the old vicous(spelling) engine fan and replacing it with a electric thermo fan. What i want to is how much CFM do i need?
Thanks Grant

Post by **plowy** » Wed Jan 04, 2006 4:06 pm

whats wrong with the standard one first

an elec fan can gives far more probs than needed

Post by **RV80** » Wed Jan 04, 2006 4:34 pm

since doing the bodylift getting the radiator at the right height and trying to remount it, its become a pain in the arse. the factory fan hits the outlet on the radiator when left in the factory location. so i've mounted up the radiator in a bit of a bodge job way. so with a thermo i can put the radiator back the original place and all should be fine.

Post by **RV80** » Wed Jan 04, 2006 4:36 pm

And i'll be setting it up with a overide switch to turn it off going through water etc

Post by **plowy** » Wed Jan 04, 2006 4:46 pm

ah ok then as for the cfm maybe try the tech section or pm dumbdunce

Post by **80UTE** » Wed Jan 04, 2006 6:16 pm

As for the CFM on the engine driven fan ??????????????? depends how fast the engine is spinning it would be 10 times the capacity of a big electric at full revs. It take approx 20 HP to drive the fan when engaged and thats how much air you need to keep it cool offroad. If you absolutley never went off road you might concider an electric fan but with any offroad they wont cut it on a big engine. The factory engineers spend a lot on research and put an engine driven fan WHY ????? because it needs it !

Wally

Post by **RV80** » Wed Jan 04, 2006 7:12 pm

So i should maybe get someone that knows what there doing to re-do the radiator mounts....

Post by **Robbo171** » Thu Jan 05, 2006 5:46 pm

just go to your local autoparts store...n look through the davies craig thermo fan catalogue.
at the back gives you sizes and CFM ratings?....from memory,i'll have to look through mine at arok again.
you'll find a thermo fan ,that will be sufficiant for your 80series.maybe 15inch or larger?

Post by **Robbo171** » Thu Jan 05, 2006 5:47 pm

just go to your local autoparts store...n look through the davies craig thermo fan catalogue.
at the back gives you sizes and CFM ratings?....from memory,i'll have to look through mine at arok again.
you'll find a thermo fan ,that will be sufficiant for your 80series.maybe 15inch or larger?

Post by **RV80** » Thu Jan 05, 2006 5:52 pm

Robbo171 wrote:look through the davies craig thermo fan catalogue.
at the back gives you sizes and CFM ratings?..

I have that part sorted. But not the factory fan CFM?

Post by **tuf045** » Thu Jan 05, 2006 8:16 pm

RV wrote:
Robbo171 wrote:look through the davies craig thermo fan catalogue.
at the back gives you sizes and CFM ratings?..
I have that part sorted. But not the factory fan CFM?

how about measuring the radiator and seeing what will fit. Don't be a tight ass and buy two small fans one big one will move more air. Maybe a fan and shroud of au six clyinder falcon might be what your after as they are twin fans with proper desgined cowl so they don't steal each others air!.

Post by **RV80** » Thu Jan 05, 2006 9:04 pm

I never said that "im going to get two small fans" i just want to do it right the 1st time. Hence the reason i asked. AU falcon fan is a good idea

i'll look into it.

Post by **tuf045** » Thu Jan 05, 2006 9:31 pm

RV wrote:I never said that "im going to get two small fans" i just want to do it right the 1st time. Hence the reason i asked. AU falcon fan is a good idea i'll look into it.

wasn't tryig to be smartass

i just learn't the hard way with doing this on a holden

Post by **RV80** » Thu Jan 05, 2006 9:37 pm

No worries

I just dont want to do it twice.

Post by **tuf045** » Thu Jan 05, 2006 9:42 pm

might want to look into the au fans because i read somwhere that they are 4 speed and the wiring can be tricky. but this could be just crap also, anyone else know?
But surely if you gave them full battery voltage they would be on full speed?

Post by **guzzla** » Thu Jan 05, 2006 10:02 pm

firstly i agree that you cant beat factory cooling systems 99% of the time and in the case of the 80's it works well.

if you get a radiator bloke to fix it, it wouldnt be a bad idea to have the top tank taken off and give the radiator a good flush n clean. had mine done a while ago and it was 40% blocked.

alternatively my experience with thermo fans has been that on large radiators with 1 large electric fan that cant cover the core fully you will develope hot spots on the tank and it will slowly overheat at idle. in this situation i solved the problem by fitting a twin fan setup off a new au falcon (about $380 from ford spare parts 3yrs ago). i tossed the shroud and fitted it to a custom alloy 1 i made and this baby cools a 400hp small block in any situation as these fans hammer.

mind u its 1 mutha of a radiator so each case is different.

IMHO get the mounts changed and stick with the engine fan, its water proof.

Post by **dow50r** » Sun Jan 08, 2006 5:11 pm

Redo the mounts and if you have ditched the cowl, get another....thermos are good to help the factory fan, but dont cut it in offroad by themselves..
Andrew

Post by **crankycruiser** » Sun Jan 08, 2006 9:43 pm

Wouldnt waste my time wid thermos..

A mate had 2 on his GQ and he ditched them real fast....

Post by **RV80** » Mon Jan 09, 2006 2:12 pm

Looks like i'll get the mounts redone. And replace the shroud that i cut the arse out of.

Outer Limits 4x4 Board

80 series eng fan cfm?

80 series eng fan cfm?

fans

fans

might

Who is online