ive got my uhf know an icom 400 pro but it says to use the scan function i need to hook up a wire to the microphone hanger could some body inform me how to do this? thanks
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
uhf help
Moderator: -Scott-
uhf help
hey people
ive got my uhf know an icom 400 pro but it says to use the scan function i need to hook up a wire to the microphone hanger could some body inform me how to do this? thanks
ive got my uhf know an icom 400 pro but it says to use the scan function i need to hook up a wire to the microphone hanger could some body inform me how to do this? thanks
lifted middy no flex, 34's twin lockers bit of doof and a wanky outers sig
Because of the Icom IC-400PRO's heritage, based on a commercial radio, you need to connect the microphone clip to negative/ground so the radio can tell if you have "finished" using the radio.
The scan function will only work if the microphone is hung up in the clip. The radio can also be programmed to do other things based on the microphones "hang up" signal, such as go into quiet mode when you hang up the microphone, but this is only of use if you want to use selcall.
A dealer can also open up the radio and disable the microphone hang up detect circuit, I've done a couple, it's not a tricky job.
I have two Icom radios (including an IC-400PRO) that use the earthed microphone clip function. I found it easier to connect each clip to negative with a short bit of wire.
Hope this helps....
Regards,
Michael.
The scan function will only work if the microphone is hung up in the clip. The radio can also be programmed to do other things based on the microphones "hang up" signal, such as go into quiet mode when you hang up the microphone, but this is only of use if you want to use selcall.
A dealer can also open up the radio and disable the microphone hang up detect circuit, I've done a couple, it's not a tricky job.
I have two Icom radios (including an IC-400PRO) that use the earthed microphone clip function. I found it easier to connect each clip to negative with a short bit of wire.
Hope this helps....
Regards,
Michael.
The IC400PRO "beep" can be turned down using the small potentiometer behind the mic socket.
The "scan-on-hook" function can be disabled also with the appropriate software, so you don't need to earth the hook ... it's optional.
But otherwise, just straight to chassis negative - same as you would any other black wire - no need to hook it up to the "earth" on the IC-400PRO ...
The "scan-on-hook" function can be disabled also with the appropriate software, so you don't need to earth the hook ... it's optional.
But otherwise, just straight to chassis negative - same as you would any other black wire - no need to hook it up to the "earth" on the IC-400PRO ...
If it's worth doing - it's worth doing to excess ...
You need a very small screwdriver to do this, and if at all possible use a non-metallic tool. If you short out the wrong thing, you could be in trouble. A small jewellers-type screwdriver should be OK as long as you aim it right!!spannercrab wrote:umm ... it's pretty much a screw which you turn with a small screwdriver - like a volume knob - clockwise makes it louder, anti-clockwise makes it softer.
Who is online
Users browsing this forum: No registered users and 3 guests