Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

suspension links

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 4583
Joined: Fri Jun 11, 2004 5:57 pm
Location: Wheeling in my backyard

suspension links

Post by sierrajim »

I've noticed that many of the OE manufacturers are now using box section and u section links. Is there any reason that everyone else uses round tube?

In all of the slider threads people say to use box instead of tube due to the strength would the same not apply for links?
[quote="Harb"]Well I'm guessing that they didn't think everyone would carry on like a big bunch of sooky girls over it like they have........[/quote]
Top
Posts: 654
Joined: Thu Nov 28, 2002 10:04 am
Location: Central Coast

Post by Bentzook »

Ive got these; sort of round but with flat sides but not square. Them are solid units. :D
You do not have the required permissions to view the files attached to this post.
"Gravitron " : drives the first layer of Gravity
Top
Posts: 10984
Joined: Thu May 29, 2003 3:47 pm
Location: Bum drilling with my buddy Ray!

Re: suspension links

Post by GRIMACE »

sierrajim wrote:I've noticed that many of the OE manufacturers are now using box section and u section links. Is there any reason that everyone else uses round tube?

In all of the slider threads people say to use box instead of tube due to the strength would the same not apply for links?
I know that u section links are design to allow a certain amount of flex (or should i say twist) in the link while still maintaining verticle strength... didnt notice new manufacturers using box section thou, and yes it is strong.
Top
Posts: 4583
Joined: Fri Jun 11, 2004 5:57 pm
Location: Wheeling in my backyard

Post by sierrajim »

the new wrangler mall (oops i mean offroad) version has box section rear lower links.

So if one were to give this a go, what material would they use? I'm going to coil the rear of the sierra, if box ends up being crap i can just make new links.
[quote="Harb"]Well I'm guessing that they didn't think everyone would carry on like a big bunch of sooky girls over it like they have........[/quote]
Top
User avatar
A1
Posts: 3451
Joined: Tue Jan 28, 2003 8:57 pm
Location: NEWCASTLE

Post by A1 »

Dave off the board with the chopped 4Runner and custom rear suspension is using shs/rhs not sure whether is was sqaure hollow section or rectangular but it is definatley box section and they cop a floggin....

Pm him and ask wat wall thickness and size he uses .




Dan
[b][i] DAN [/i] [/b]


:silly:
Top
User avatar
Guy
Posts: 10366
Joined: Thu Dec 12, 2002 8:43 am
Location: Wangaratta

Post by Guy »

http://www.claytonoffroad.com make their "hardarm" suspension links from what appears to be RHS and is rumoured by most to be neigh on unbreakable..

I think ABT sell clayton stuff as well ..

http://www.abt4x4.com/index.php?PCID=26 ... imary&CDO=
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 3 guests