Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

help needed- tie rod end pin spinning

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 309
Joined: Sun Mar 05, 2006 9:00 pm
Location: Melbourne

help needed- tie rod end pin spinning

Post by ash_on_mtb »

I've had the steering box out of 'runner (non PS) to "reco" it for RWC, gone to do up the tie rod end of the panhard rod, and the pin that runs into the rod end is spinning before its tight enough to get the split pin in... How do I hold it to get a couple more turns out of it?? I can't get at the top of it, and by pushing the rubber seal thing up, I can't grip the shaft...

any ideas? Are they even supposed to turn?? Can you access the top of the pin??

thanks for your help, I have a vision of the nut unwinding without the split pin.. and I need to use it tommorrow. :?
Last edited by ash_on_mtb on Tue Mar 21, 2006 7:08 pm, edited 1 time in total.
'97 HDJ80 - worth the wait
Top
Posts: 309
Joined: Tue Dec 03, 2002 11:43 am
Location: SOMEWHERE IN VICTORIA

Post by TUFF MAV »

Try using a bar to lever the tierod up into the taper while you do the nut up.

Kyle
BUGGERED IT'S A TOYOTA THING
Top
Posts: 309
Joined: Tue Dec 03, 2002 11:43 am
Location: SOMEWHERE IN VICTORIA

Post by TUFF MAV »

Try using a bar to lever the tierod up into the taper while you do the nut up.

Kyle
BUGGERED IT'S A TOYOTA THING
Top
Posts: 2066
Joined: Mon Jun 09, 2003 8:17 pm
Location: Gympie

Post by Rhett »

clamp it down somehow. If you ably lotsa pressure pushing the pin into the tappered hole it should grip.
Its a wheelbase thing
Top
Posts: 736
Joined: Mon Mar 07, 2005 5:25 pm
Location: Redcliffe, Brisbane

Post by chops »

buzz it down with a rattle gun..usually works
1988 351W GQ wagon
Top
Posts: 309
Joined: Sun Mar 05, 2006 9:00 pm
Location: Melbourne

Post by ash_on_mtb »

cheers folks, took a mattock to get it out, off to the shed to find something big and ugly to put it back in with :D
'97 HDJ80 - worth the wait
Top
Posts: 309
Joined: Sun Mar 05, 2006 9:00 pm
Location: Melbourne

Post by ash_on_mtb »

and buggger me if it wasn't the mattock that got it back in!! Levered it up using the mattock, which squashed it all together and its all good.

Thanks for helping me out of a pinch. :armsup:
'97 HDJ80 - worth the wait
Top
Posts: 3099
Joined: Wed Dec 11, 2002 10:55 am
Location: Central Queensland

Post by BundyRumandCoke »

I know its done, but use a floor jack to jack it up into the taper.
Mud makes excellent toothpaste.
Top
Posts: 1397
Joined: Sat May 29, 2004 6:58 pm
Location: West Australia Posts: Less than DeWsE

Post by jeep97tj »

Hahaha mattocks are very handy, I used 1 between my diff and steering rod to straighten it, worked a treat :cool:
Shane
Top
Posts: 1489
Joined: Wed Jan 21, 2004 4:13 pm
Location: Brisbane South. QLD

Post by G_loomis »

BundyRumandCoke wrote:I know its done, but use a floor jack to jack it up into the taper.
as Meatloaf once said "you took the words right out of my mouth"...

please note I left the kissing part out! :cool: dont go there!
L.S Canvas & P.V.C
www.lscanvas.com.au
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 6 guests