Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

thread size for a 2H glow plug

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 3523
Joined: Fri Aug 27, 2004 12:27 am
Location: Fairfield,Sydney

thread size for a 2H glow plug

Post by pongo »

Basically as the title says. I need a 14 volt glow plug for a project and these seem to be the only ones i can find.

I need to know the size so i can try and find a thread tap to suit before i get too carried away.


Thanx guys, and ill reveal all once i get this project sorted out ;)
Top
Posts: 6
Joined: Mon Aug 30, 2004 7:10 pm
Location: Brisbane

Post by KingOffTheRoad »

M10 x 1.25 :cool:
HJ47 Troopy - Rear Air locker, 3" lift, 33 claws, Marks transfer gears, 60 Pwr Steer.
Top
Posts: 5179
Joined: Fri Dec 05, 2003 8:15 pm
Location: Brisbane Australia

Post by Shadow »

its a pretty uncommon thread from what i can gather, was trying to make up a compression tester for my 2H but the thread wasnt normal (measured em with a thread guage but cant remember what it was)
Top
Posts: 286
Joined: Mon Jul 25, 2005 8:06 pm
Location: N.Q.

Post by bigbrowndog »

10x 1.25 mm
Top
Posts: 3523
Joined: Fri Aug 27, 2004 12:27 am
Location: Fairfield,Sydney

Post by pongo »

thanx, Now to find a tap.

Cheers
Top
Posts: 3349
Joined: Tue Nov 23, 2004 10:29 am
Location: Not where you are

Contact:
Contact Gribble

Post by Gribble »

Its not that uncommon on most japanese cars/trucks. Finding a tap should be dead easy.
\m/
Top
Posts: 3523
Joined: Fri Aug 27, 2004 12:27 am
Location: Fairfield,Sydney

Post by pongo »

found a tap, got my glow plugs in the mail today, Then i wondered what size drill bit i need to use. I have never had to do a tap before .

Im guessing a 10mm, but im unsure.

Help please ?

Cheers
Top
Posts: 183
Joined: Wed Nov 12, 2003 4:52 pm
Location: Brisbane

Post by Tooheys »

usually 9mm but this chart http://www.engineersedge.com/tap_drill_chart.htm says 8.8mm.......hmm dont even know if that size exists in drill bits
If at first you dont succeed.......get a bigger HAMMER!!!
Top
Posts: 442
Joined: Thu Nov 11, 2004 12:14 pm
Location: Boomba boys drive bodied rigs

Post by batcho101 »

make sure u use the 8.8 drillbit otherwise the thread wonr be a tight fit it will slop around and wont seal properly..if your using glow plugs for sumthing i gather it might have compression so use the right drill and tap first time. cheers batcho
84lux-project. A-frame, 350 chev, turbo 350 auto, duals, rears up front, crossover, twin locked and a 118" wheelbase
Top
Posts: 3523
Joined: Fri Aug 27, 2004 12:27 am
Location: Fairfield,Sydney

Post by pongo »

Thanks guys :armsup: .

Have a virtual beer on me :P
Top
Posts: 101
Joined: Wed Feb 23, 2005 1:27 pm
Location: Nth.Brisbane Qld.

Post by NiftyNev »

An 11/32 drill bit will be much easier to find.

http://www3.telus.net/public/aschoepp/tapdrill.html

Nev
'92 Toyota Surf LN130
2.4 Turbo Diesel
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 4 guests