Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
4bd1t fuel economy
Moderator: Micka
4bd1t fuel economy
what fuel economy can you expect from a 4bdit and where would i look for conversion parts for a 5 speed 85 Rangie ???
Got one behind a 6.2 chev diesel thats done 100k since new bearings and synchro's and its fine, N/A but still??Bush65 wrote:An 85 rangie would have an LT77, which is far too weak to use behind a 4BD1.
Even the LT85's don't stand up the 4BD1 unless modified.
Wanted: Car trailer or beaver tail truck, let me know what you got
I disagree John, IME they seem to hold up reasonably well, the one in my truck lasted 300000km before needing a rebuild (done by Mal Story at po's expense), and the one in a mate's 110 outlasted the engine!!! (but admittedly the engine died prematurely at about 300k km). This gearbox is still going strong, (50k km after engine rebuild) only problem is some play in 3rd.Bush65 wrote:An 85 rangie would have an LT77, which is far too weak to use behind a 4BD1.
Even the LT85's don't stand up the 4BD1 unless modified.
Back on to fuel consumption, my 4BD1 uses 9-11L/100km, depending on how hard I am puhing it on the highway.
Last edited by ISUZUROVER on Tue Jul 11, 2006 7:54 pm, edited 2 times in total.
_____________________________________________________________
RUFF wrote:Beally STFU Your becoming a real PITA.
Already sounds a bit like a racing truck, 'cause I removed all mufflers on the standard exhaust, but I reckon it'll go really well, especially having the outlet just tucked up in front of the left rear wheel/tyre.
Tweaking the fuel pump begins in two weeks time, when I get back to FNQ. I expect the consuption to go up in a big way. Cheers...
Tweaking the fuel pump begins in two weeks time, when I get back to FNQ. I expect the consuption to go up in a big way. Cheers...
Cheers, Gerry........
7/87 110 County Isuzu 3.9TDI, Maxi Front n Rear.
7/87 110 County Isuzu 3.9TDI, Maxi Front n Rear.
I'm getting 19 mpg towing a 1.2 ton poptop van at highway speeds. uphill and into headwinds, it seems to stay the same.
Without the van, about 24 mpg driven sensibly.(My wife says I can't drive sensibly...)
If I wound the fuel back I would be getting about 28 mpg, but it wouldn't be as much fun...
BTW, I'm on holidays and the RR is still at home waiting for its Allison auto conversion.
LS400 is nice to drive though...
JC
Without the van, about 24 mpg driven sensibly.(My wife says I can't drive sensibly...)
If I wound the fuel back I would be getting about 28 mpg, but it wouldn't be as much fun...
BTW, I'm on holidays and the RR is still at home waiting for its Allison auto conversion.
LS400 is nice to drive though...
JC
'92 Rangie Sherwood/turbo intercooled isuzu4BD1 /ACE/ full leather/2.5" exh/2.5" body lift/DeCarbon shocks/LR tanks/LT95 back in and OK now, Sals conversion soon...
I will soon be selling an Isuzu MSA-5P gearbox which has been modified to fit an 85 Rangie.
It's had an extended shifter grafted onto it to protrude in the same place as your factory box. WIll come with an adaptor shaft to an LT230 gearbox.
To fit and work it will need:
1. An Isuzu 4B series engine.
2. The back housing off an LT77 box.
3. A 75mm aluminium adaptor plate which I can provide all the dimensions for.
I may be able to sell part #3 as well, depending on how my plans proceed.
New bearings before installation would be a good idea. No noise when driven but it's not as tight as the MSA-5G I'm replacing it with.
I recently installed a 1:1 ratio LT230, I now get 11km/l on a flat level run. That's a hair over 30MPG.
Was getting approx 9.5 km/l with the 1.2:1 ratio LT230.
It's had an extended shifter grafted onto it to protrude in the same place as your factory box. WIll come with an adaptor shaft to an LT230 gearbox.
To fit and work it will need:
1. An Isuzu 4B series engine.
2. The back housing off an LT77 box.
3. A 75mm aluminium adaptor plate which I can provide all the dimensions for.
I may be able to sell part #3 as well, depending on how my plans proceed.
New bearings before installation would be a good idea. No noise when driven but it's not as tight as the MSA-5G I'm replacing it with.
I recently installed a 1:1 ratio LT230, I now get 11km/l on a flat level run. That's a hair over 30MPG.
Was getting approx 9.5 km/l with the 1.2:1 ratio LT230.
3incher
Got the 3 inch mandrel bent side exit fitted just before I left for work, sorry no photo's till I get back. It goes much better off the mark, taking far less time to spool, and expelling heat much more efficiently, the bulkhead is cool after a decent run, missus delighted. Even better, it sounds like a military tank, obsolutely wicked!. Oddly enough with the side windows up, the vehicle is much quieter than with the old standard exhaust!. Initial fuel figures look promising, as yet I have not adjusted the pump, on a run across to Einsleigh Pub, via Georgetown, and back via The Lynd, consumption was just under 12ltrs/100k, and we had the vehicle fully loaded - not bad...can't wait to get back & head back up the Cape for a spot of fishing ....
Cheers, Gerry........
7/87 110 County Isuzu 3.9TDI, Maxi Front n Rear.
7/87 110 County Isuzu 3.9TDI, Maxi Front n Rear.
Who is online
Users browsing this forum: No registered users and 0 guests