Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Hilux LN106 Bodylift
Moderators: toaddog, Elmo, DUDELUX
Hilux LN106 Bodylift
What has to be done to the rest of the truck, when a bodylift is done. I wanted a 2 inch bodylift, but am not sure on what else I'll have to do to make it all work properly?
Any info appreciated
Cheers
Craig
Any info appreciated
Cheers
Craig
diesel028 wrote:What about the radiator, gearsticks and steering shaft?? Nothing at all had to be done?
Cheers
Craig
just loosen the slip joints on the steering ahft 2 allow it 2 pull apart a littlebit and u will have no dramas.
the gearsticks should b fine on a 2" any bigger and u will have trouble.
the radiator should also b ok u may need 2 take off the bottom part of the cowling or u can lower it 2" f u want but being a diesel u will b right..
HYPOFAB
Thanks to:
Polyperformance
Yuri 4x4
Longfield
Thanks to:
Polyperformance
Yuri 4x4
Longfield
Old Yella wrote:don't bother with a 2" lift I started with 2 1/2 " and went to a 3" after 2 years because any tyres over 32" scrub on a 2" lift.
i disagree, i have a 2 inch body and about 1.5 in the springs and i run 35's with out a drama.
The only advantage i can see, on my truck, in having a three inch body lift is the fact that i could then run the winch from behind the front cross member.
When i fitted my 2 inch body lift i had to trim the tunnel for the gear stick to shift to 5th and reverse and also lower the rad as they are different in the 4 runner to the hilux.
NICK
TECH SCREW GURU
I just did a 2.5" body-lift on my lux 2 days ago.
I have an RN105 with a 22R, I had to chop about 10mm off the ends of
the fan cause the bottom pipe is directly under the fan in my truck.
Everything else fitted OK I just had to slightly bend a few brackets etc.
The rubber gear-boot on my lux fits, but it makes 2nd and 4th a little
harder to get into, so I removed the boot and it works fine now.
AND free heat from the exhaust too
I bought a steering spacer off Chaos4x4 too cause I didn't like the lack
of spline-age in the unis. But my mate did a 2.5" on his 4Runner and
like hypo said, he just slacked off the spline bolts and let it slip out
a bit. His never fell out.
Be careful if your steering unis are a bit old/rusty. I killed one by
accident trying to force it off the shaft with a bit of mallet-work.
Cheers,
Bart
I have an RN105 with a 22R, I had to chop about 10mm off the ends of
the fan cause the bottom pipe is directly under the fan in my truck.
Everything else fitted OK I just had to slightly bend a few brackets etc.
The rubber gear-boot on my lux fits, but it makes 2nd and 4th a little
harder to get into, so I removed the boot and it works fine now.
AND free heat from the exhaust too
I bought a steering spacer off Chaos4x4 too cause I didn't like the lack
of spline-age in the unis. But my mate did a 2.5" on his 4Runner and
like hypo said, he just slacked off the spline bolts and let it slip out
a bit. His never fell out.
Be careful if your steering unis are a bit old/rusty. I killed one by
accident trying to force it off the shaft with a bit of mallet-work.
Cheers,
Bart
Thanks for your answers guys.
I think I'll try a 2" bodylift to start with as I already have 2" suspension lift and am running 33's. Will also be getting 2" extended shackles a bit later on. Then eventually will run 35's.
My next question is, what type of block is better? An aluminium/steel or the nylon type ones?
Cheers
Craig
I think I'll try a 2" bodylift to start with as I already have 2" suspension lift and am running 33's. Will also be getting 2" extended shackles a bit later on. Then eventually will run 35's.
My next question is, what type of block is better? An aluminium/steel or the nylon type ones?
Cheers
Craig
I'd go nylon if I had the choice but in Qld we must use metal ie alum or steel.
I run 35" with no body lift and reasonably flat springs with lowered mounts. I think that I'd almost have enough clearance in the front for 37" but for the reat, the tray would need reworking.
I run 35" with no body lift and reasonably flat springs with lowered mounts. I think that I'd almost have enough clearance in the front for 37" but for the reat, the tray would need reworking.
TEAM DGR WEBSITE
TEAM DGR ON FACEBOOK
Sponsors:
SUPERIOR ENGINEERING
LOCKTUP 4X4
UNIVERSAL DRIVESHAFTS QUEENSLAND
MASSOJET UNDER BODY BUDDY
DIRTCOMP
4WD TV
TEAM DGR ON FACEBOOK
Sponsors:
SUPERIOR ENGINEERING
LOCKTUP 4X4
UNIVERSAL DRIVESHAFTS QUEENSLAND
MASSOJET UNDER BODY BUDDY
DIRTCOMP
4WD TV
diesel028, M&G Industrial in Fyshwick sell UHDPE engineering rod, they can cut it to length and drill it for you as well. Probably about $150 for enough blocks to do the body and the tub. There is a size about 70mm dia, that is the one you want..
Then go around the corner to Specialty Fasteners and get some grade 8 zinc plated bolts (with nylocks) 50mm longer than your existing ones. Get washers as well, as the toyota ones are held captive on the bolts. I can give you a hand to put it all in if you want, I live around the corner from Damien.
Then go around the corner to Specialty Fasteners and get some grade 8 zinc plated bolts (with nylocks) 50mm longer than your existing ones. Get washers as well, as the toyota ones are held captive on the bolts. I can give you a hand to put it all in if you want, I live around the corner from Damien.
Ultra High Density Poly Ethelyene
(Nylon if you must)
(Nylon if you must)
MY JEEP BUILD
v840 wrote: [Not a shot at Tonka] It's like saying, hell I've got two nuts, I may as well cut one of them off for the hell of it. I ain't using it.[/NAS@T] It's ridiculous!
I used the same stuff and bought a 1meter rod of it for $35 and cut it and drilled it myself. Was the cheapest way.
MY JEEP BUILD
v840 wrote: [Not a shot at Tonka] It's like saying, hell I've got two nuts, I may as well cut one of them off for the hell of it. I ain't using it.[/NAS@T] It's ridiculous!
I just used a drop saw to cut them, then put them on a lathe to tidy them up, but this really is not needed.
I used a drill press to get straight holes, but a power drill and vice would work too.
I used a drill press to get straight holes, but a power drill and vice would work too.
MY JEEP BUILD
v840 wrote: [Not a shot at Tonka] It's like saying, hell I've got two nuts, I may as well cut one of them off for the hell of it. I ain't using it.[/NAS@T] It's ridiculous!
Posts: 3523
Joined: Sun May 18, 2003 8:42 pm
Joined: Sun May 18, 2003 8:42 pm
Location: Somewhere they can't reach me, shoot me or electrocute me...
No idea what blade, whatever was in it at the time
The lathe fixed up the mess, but it really wasn't that bad.
The lathe fixed up the mess, but it really wasn't that bad.
MY JEEP BUILD
v840 wrote: [Not a shot at Tonka] It's like saying, hell I've got two nuts, I may as well cut one of them off for the hell of it. I ain't using it.[/NAS@T] It's ridiculous!
Who is online
Users browsing this forum: No registered users and 0 guests