Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

MK SD33T no power - please help!!

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Post Reply
Posts: 247
Joined: Wed Apr 19, 2006 9:13 pm
Location: Perth

MK SD33T no power - please help!!

Post by 84mksd33t »

hey
my 1984 mk sd33t is extremely hard to start - would fire on 2 cylinders and then stall. it took 6 or 8 attempts of lengthy glowing and starting before it would start. i then primed it using the hand pump - when i initiated the pumping alot of air burst out and then i was able to pump.

once i got it started the following happened - this was when it was fully warm

- would not rev - very very slow revving i could get to 2800rpm but usually
- couldnt get out of 2nd gear on the road
- diesel filter is leaking (the one near the fire wall) has been for a few weeks
- it is firing on all 6 cylinders once warm so injectors are ok?

i have removed the air filter incase that was blocked.

what could be causing this?
- leaking fuel filter is letting air into the fuel system and thus not giving me pure fuel?
- faulty injector pump (i have had the fuel increased accordingly to compensate for increased boost)
-faulty injectors?
-glow plugs? (they are only used for cold starts right?)

Any suggestions are welcomed as this is my weekend rig and i need to take my cr500 to the dunes this Sunday!!!!

Cheers guys!

Cody
Last edited by 84mksd33t on Sun Oct 08, 2006 4:34 pm, edited 1 time in total.
Posts: 16
Joined: Sat Feb 04, 2006 8:48 pm
Location: Yamanto

Post by elmo72j »

I would be looking at the leaking fuel filter as a start it is probably letting air in to the system. Check the top of the injector pump as well to see if there is any leaks, that can cause problems as well.

Johno
Posts: 965
Joined: Fri Mar 26, 2004 10:09 am
Location: B.F.E

Post by RMP&O »

Yup leaky fuel system will cause this, ie sucking air. Dirty filter will contribute as well. Start with the fuel system and get it all in order.
www.rmp-o.com
Posts: 4792
Joined: Sun Nov 21, 2004 9:05 pm
Location: Watching out for stray buses

Post by Brendan-s »

yeah most definetly i'd say air in fuel somewhere. had the same problem for about a month where it would be intermittent but under hard load would stall out -- turns out to be a split in the fuel line right back at the tank that would only expand enough to let air in under load
Posts: 49
Joined: Thu Feb 02, 2006 10:53 am
Location: West Sydney

Post by herks »

Yeh and a look at the primary fuel filter in the banjo coupling where the fuel line joins the bottom of the lift pump. You may find that this is partially blocked which will also cause this type of thing.
Posts: 247
Joined: Wed Apr 19, 2006 9:13 pm
Location: Perth

Post by 84mksd33t »

hey guys
i changed the filter near the firewall - this stopped the sucking noise i could hear previously. but the car still wont start.

what else can i look for?

I have primed the pump manually and alot of diesel is coming through.

are there any tricks i should know about?

I need the patrol up and going so i can move some furniture later !!!
Posts: 533
Joined: Sat Jan 15, 2005 4:54 pm
Location: Melbourne, Australia.

Post by InSanE »

check your glowplugs mate you could have a few glowplugs out or your glowplug timer module isnt working, first turn the ignition on and make sure you have voltage at the glowplugs, then if u do take the rail that joins the glowplugs off and test each glowplug btween the top of the plug and the head with a multimeter set to check resistance and each glowplug should give you a reading, if it doesnt it means it is u/s and must be replaced
GQ LWB TD42, boost, lockers etc

http://forum.mudrhino.com.au/viewtopic.php?t=262&start=30
Posts: 247
Joined: Wed Apr 19, 2006 9:13 pm
Location: Perth

Post by 84mksd33t »

gunna check the glow plugs now

this is what is causing the problem - i think....

the bearing for this little doohickey is stuffed. the electric motor can no longer turn it - it initiates the injector pump doesnt it?

Image

is there a manual setup i can use to get the doohickey moving again?
Posts: 625
Joined: Fri Feb 20, 2004 12:04 am
Location: Melbourne

Post by Woop »

Try disconnecting the rod from the actuator and setting the arm on the injection pump in the RUN position. See if it starts then. There is a fair bit of discussion on www.binderbulletin.org about problems with the actuator.

Nick
Posts: 247
Joined: Wed Apr 19, 2006 9:13 pm
Location: Perth

Post by 84mksd33t »

Trying now!!

Out of interest

what is stop
what is run
and what is start

which positions for each function on the actuator?
Posts: 625
Joined: Fri Feb 20, 2004 12:04 am
Location: Melbourne

Post by Woop »

Havent got the manual to hand, but from memory, there are 3 positions for the arm on the pump. Start,STOP and RUN. I think when starting, the lever moves to the START position, then moves back to RUN when the engine starts. Lever moves back to STOP to stop the engine. The actuator motor controller is controlled by a box that among other inputs, has a feed from the oil pressure sender. If no oil pressure (engine running in reverse--can happen with inline type injection pump), controller will send signal to the actuator to shut the engine down.

Nick
Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest