Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Click Click Click when turn on ignition and engine does not

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 588
Joined: Wed Mar 09, 2005 7:04 pm

Click Click Click when turn on ignition and engine does not

Post by gotoy »

Went to start my truck this morning, after not doing so for 6 days. Usually I just do the glow plugs and starts right away.
Today had a click click click sound and no action.
I am assuming the click click is the solenoid. Well I am off to check the battery and use a hammer on the starter.

Screwed up my next 2 days its a holiday here! :cry: :cry: :cry: :cry:
Top
Posts: 156
Joined: Tue Sep 27, 2005 7:23 pm
Location: Dandenong ranges

Post by Dyna Beast »

Might be that your starter motor is a bit dodgy.If my truck is not fully charged it will not have enough power to activate the starter solenoid. Same thing that is posibly happening to you.
Cheers
Hybrid rover ute. Isuzu diesel. Custom suspension. Winch. Snorkel etc. etc.
Top
Posts: 7230
Joined: Mon Oct 21, 2002 10:42 pm
Location: Brisbane

Post by MissDrew »

Will either be flat battery or the contacts in the starter have died.
Top
Posts: 588
Joined: Wed Mar 09, 2005 7:04 pm

Post by gotoy »

Seems one of my dual batteries was a little thirsty. They are both in parrallel but always seems to be the same one with low battery water; they are not sealed units fyi.

Any thanks for the advice and I'd better have my starter motor checked out.
Top
Posts: 1
Joined: Mon Oct 23, 2006 8:11 pm

Post by BadBear »

My Hilux did a similar thing on a recent trip to the Cape. I had to replace the contacts on the solenoid and the auto electrician fitted better 'half moon' shaped heavy duty ones. Whilst it was out they also replaced the bearings in the starter.
Top
Posts: 212
Joined: Tue Sep 07, 2004 9:28 am
Location: Panama, Central America

Post by Mario »

Happened to me once in my GQ. There´s a solenoid before the solenoid integrated to the starter. Replaced that solenoid (the first one) and my problems were cured. Check to see if your Toyota setup is the same.
Good luck...
Top
Posts: 27
Joined: Tue Mar 28, 2006 7:29 am
Location: Blenheim, NZ

Post by muddy12 »

Before you start spending money, check all your earth leads have good clean contacts both ends - battery to chassis, battery to engine, and engine to chassis. You need to unbolt the cables & clean them up so there's no rust and a good clean metal to metal contact. It's often only good enough to let a low current through (like when you use a tester), but not enough for the full cranking current. Ask how I know? After rebuilding the starter & it still wouldn't work....
Top
Posts: 1254
Joined: Mon May 16, 2005 8:21 pm
Location: Sth Brissy

Contact:
Contact LuxyBoy

Post by LuxyBoy »

Mine did this when i went to a The Springs 4x4x Park. Had to drive back to Warwick to get a new battery into it :bad-words:
Kind Regards,
Brad
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 7 guests