Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Rear axle bearings and seals.
Moderators: toaddog, Elmo, DUDELUX
Rear axle bearings and seals.
Hi all
Im gunna change the rear axle bearing and seals when i fit the locker into my 85 4runner. I just went down to the local bits shop and got quoted $80 per side. Is this the going price or does anyone have any contacts or suggestions for me to get them?
Also while ive got it pulled apart is there any other suggestions on what to change? Its all running ok at the moment im just doing some preventative maintenance.
Ill be doing this at home so does anyone have any tips on doing the axle bearings to make it easier?
Thanx Matt
Im gunna change the rear axle bearing and seals when i fit the locker into my 85 4runner. I just went down to the local bits shop and got quoted $80 per side. Is this the going price or does anyone have any contacts or suggestions for me to get them?
Also while ive got it pulled apart is there any other suggestions on what to change? Its all running ok at the moment im just doing some preventative maintenance.
Ill be doing this at home so does anyone have any tips on doing the axle bearings to make it easier?
Thanx Matt
I just did the rear bearings on mine and I tell you they are the biggest PIA to get off. I couldn't press them off as they are behind the soft drum brake backing so I had to cut them. I would happily have paid $80 per side to have them done for me in hindsight, and that's not a bad price.
If only they were like the front IFS hub ones that actually fall out once everything is undone.
Did you buy a bearing kit? You should have a new outer axle seal (o ring) and a new inner oil seal as well, plus a rubber bearing seal i think it was... Make sure you get the new inner oil seal nice and square and dont bend it
Not sure what a manual will say but i'm sure it will want you to pull the engine out to do the rear bearings
You don't have to take out the brake shoes, just disconnect the brake lines and pull out the hand brake cable for each side. Undo the 4 rear bolts and it should come off. If it's stubborn; Try putting the drum housing back on back to front with a few wheel nuts, then you can use it as a slide hammer to get the axle out
If only they were like the front IFS hub ones that actually fall out once everything is undone.
Did you buy a bearing kit? You should have a new outer axle seal (o ring) and a new inner oil seal as well, plus a rubber bearing seal i think it was... Make sure you get the new inner oil seal nice and square and dont bend it
Not sure what a manual will say but i'm sure it will want you to pull the engine out to do the rear bearings
You don't have to take out the brake shoes, just disconnect the brake lines and pull out the hand brake cable for each side. Undo the 4 rear bolts and it should come off. If it's stubborn; Try putting the drum housing back on back to front with a few wheel nuts, then you can use it as a slide hammer to get the axle out
Last edited by -Nemesis- on Tue Nov 28, 2006 3:06 pm, edited 2 times in total.
Lovin the FZJ105-T, bling by Ryano
Im here for the sausage!
http://www.4x4wire.com/toyota/maintenan ... l_bearing/
This might help.
Don't worry about SSTs or presses, the shade tree method works best and is very quick, then simply tap them back onto the axle with a drift. Took me about ten minutes per side to get them on and off.
Have fun
This might help.
Don't worry about SSTs or presses, the shade tree method works best and is very quick, then simply tap them back onto the axle with a drift. Took me about ten minutes per side to get them on and off.
Have fun
[quote="barnsey"]smoked Elle McPherson, even though I didn't inhale[/quote]
[url=http://www.outerlimits4x4.com/PHP_Modules/phpBB2/viewtopic.php?p=765579&highlight=#765579/]Roadrunners Hilux[/url]
[url=http://www.outerlimits4x4.com/PHP_Modules/phpBB2/viewtopic.php?p=765579&highlight=#765579/]Roadrunners Hilux[/url]
Hi
I just had to do my rear ones. $80 per side seems a bit steep. I picked up a wheel bearing kit (bearing and all seals) for $38 per side. From BWS Bearings in ringwood.
I know of the backyard way to do them but i just couldn't be bothered. i just pulled the axles and brought them to the local 4x4 place. he charged be $70 to replace both.
Then i just got home and put them back in. i was happy to pay as they can be a real pain.
I just had to do my rear ones. $80 per side seems a bit steep. I picked up a wheel bearing kit (bearing and all seals) for $38 per side. From BWS Bearings in ringwood.
I know of the backyard way to do them but i just couldn't be bothered. i just pulled the axles and brought them to the local 4x4 place. he charged be $70 to replace both.
Then i just got home and put them back in. i was happy to pay as they can be a real pain.
So much money to spend, So little income.
yeah i did min earlier in the year.
wont be doing that again!
happily pay to have some one else change the bearsing over.
i would do as mudlux has,pull the axles out and get the old ones pressed off and the new ones pressed on and then just bolt your axles back in.
i think i paid about $80 or $90 for kits for both sides aswell.
cheers
Dom
wont be doing that again!
happily pay to have some one else change the bearsing over.
i would do as mudlux has,pull the axles out and get the old ones pressed off and the new ones pressed on and then just bolt your axles back in.
i think i paid about $80 or $90 for kits for both sides aswell.
cheers
Dom
85 LN65 D/cab locked with 35's
77 RA28 celica-in parts in perth
77 RA28 celica-in parts in perth
Got the bearing from Don Kyatt in seven hills for $46 a side!!!! Got home , stripped it down to get cracking on it and the locker , only to find my pinion is stripped! Stuff knows how it was still driving.
Now i need to get a 4.88 pinion quick smart.
Nemesis check your PM's ill take the one your selling...LOL
Now i need to get a 4.88 pinion quick smart.
Nemesis check your PM's ill take the one your selling...LOL
Chaps, a little trick I use for getting the bearings off, since the backing plates wont allow normal pullers to be used.
I cold chisel the lock ring in several places to expand it.
Place a solid block of wood on the floor.
with axle flange/ backing plate facing up, and holding backing plate.
I lift them up, and then drop it down onto the timber (timber stops the splines from being damaged).
Sort of like using a crow bar to pack soil, let the weight of the axle do its work, dont try and belt it down on the wood.
Usually 3 to 5 taps and the bearing is free, no damage to anything, and nice and quick.
Pressing on is easy, just make sure you put the seal on correctly
Cheers
Trains
I cold chisel the lock ring in several places to expand it.
Place a solid block of wood on the floor.
with axle flange/ backing plate facing up, and holding backing plate.
I lift them up, and then drop it down onto the timber (timber stops the splines from being damaged).
Sort of like using a crow bar to pack soil, let the weight of the axle do its work, dont try and belt it down on the wood.
Usually 3 to 5 taps and the bearing is free, no damage to anything, and nice and quick.
Pressing on is easy, just make sure you put the seal on correctly
Cheers
Trains
Save the Whales......Collect the whole set.
My Wife Can't Shear..............But You Should See Her Crutch !
My Wife Can't Shear..............But You Should See Her Crutch !
Who is online
Users browsing this forum: No registered users and 18 guests