Notice: We request that you don't just set up a new account at this time if you are a previous user. If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
oh, we were trying.....
the lower section of that ledge was almost vertical and VERY slippery... but we made it up... he had no option as his winch was dying
Here is my 82 four door limo.
Had a 4.3 litre stroker but I popped it so it's a 3.5 at the moment.
Diffs are laminated housings with Maxi Drives front and rear.
Hi tough nickel alloy axels and Haultech CVs.
Tyres are Simex ET's 35 x 10.5 x 16.
Has LPG as well as petrol with sill tanks.
ARB bar with Warn hi-mount winch.
Garmen 128 GPS.
Heaps of dents and scratches.
I love it
Andy
You do not have the required permissions to view the files attached to this post.
Good model and colour, same as mine. Just needs a ZF auto and it will be perfect (mine's being fitted as we speak, by me of course ). I also have a 4.3 stroker block at home, ready to be rebuilt one day sometime
Aquarangie wrote:Just needs a ZF auto and it will be perfect
Trav, I put a vehicle over backwards during round three of the winch challenge in 2002 (see photo) and Glen Binskin repeated it right behind me, trust me...I like to have a clutch pedal I just wish I had jumped on it earlier.
Andy
You do not have the required permissions to view the files attached to this post.
landy_man wrote:oh, we were trying..... the lower section of that ledge was almost vertical and VERY slippery... but we made it up... he had no option as his winch was dying
Tell em the real story.... I was driving up and would have made to the top but some nooooob parked his baby blue POS in the way and I stop in fear of getting baby blue paint on my car (which BTW i did) and then had all soorts of pain going again
landy_man wrote:oh, we were trying..... the lower section of that ledge was almost vertical and VERY slippery... but we made it up... he had no option as his winch was dying
Tell em the real story.... I was driving up and would have made to the top but some nooooob parked his baby blue POS in the way and I stop in fear of getting baby blue paint on my car (which BTW i did) and then had all soorts of pain going again
cough*bullchit*cough... you were already past me... that is why u rolled BACKWARDS into my POS
landy_man wrote:oh, we were trying..... the lower section of that ledge was almost vertical and VERY slippery... but we made it up... he had no option as his winch was dying
Tell em the real story.... I was driving up and would have made to the top but some nooooob parked his baby blue POS in the way and I stop in fear of getting baby blue paint on my car (which BTW i did) and then had all soorts of pain going again
cough*bullchit*cough... you were already past me... that is why u rolled BACKWARDS into my POS
Rangie Ute 79
bob tailed flat bed (was style side) shortened chassis raised fuel tank
4'' tube bed with rollbar and 4 hella 4000 spotties
4.5 l efi, rover heads, extractors,4bl inlet manifold.twin thermos
lt95 box
2.5 straight through exhust
belt driven compressor runs all my rattle guns off eng.
dual bats
snorkel
custom trailing arms, strenthened tailshafts
custom steering arms and panard rod.(needs it with 38")
under body lights
4'' coil & 2'' body
custom offset 15x10 rims(approx 12inches widen track when fitted)
38'' swampers, pissy looking 31'' on the road.
Air bead locks
Maxi drive locker rear end, open front end.
rock slider steps, custom front bar(swap with some1 for a winch bar)
8 point internal roll cage.
Daytona bucket seats with 4 pt harnesses.
No carpet all steel an alloy checkerplate
down the track:
front maxi drive and a winch bar
also a new lt95 box.
6.2 chev, kicking ourselves when we sold our last rangie with a 6.2.
You do not have the required permissions to view the files attached to this post.
Here's mine.... stock 'cept for TJM winch bar (no winch) and centre diff lock actuator. On their way from Melbourne are a set of Rock sliders. In near future, Front locker (diff had some dental work), 2 inch lift (shocks stuffed and springs sagging) and 265x75R16 muddies (tyres bald).
Cheers
Paul
You do not have the required permissions to view the files attached to this post.
Message content not approved for consumption by children or easily damaged psyches. If accidentally exposed, flush eyes with cold water and induce vomiting. If irritation persists, sit quietly and watch SBS.
You do not have the required permissions to view the files attached to this post.
Message content not approved for consumption by children or easily damaged psyches. If accidentally exposed, flush eyes with cold water and induce vomiting. If irritation persists, sit quietly and watch SBS.