Page 2 of 2
Posted: Tue Mar 16, 2004 11:58 am
by ISUZUROVER
What is the rest of the CV like???
Posted: Tue Mar 16, 2004 4:00 pm
by landy_man
Okay....
went to pick up my 4.8 high pinion today..."sorry mate, it is a 4.5" - so I have now bought a high pinion 4.5 and low pinion 4.5 for the rear...
The wrecker was very cool as he swapped one of my 4.8 lows for a 4.5 low...AND I DID NOT EVEN BUY THE 4.8 from him
RUFF - No thanks, mine look a little nicer than yours.....on the phone to Terra again
Posted: Tue Mar 16, 2004 4:01 pm
by landy_man
red90 wrote:So i sthe broken CV a Longfield or a Profield?
Long I believe
Posted: Tue Mar 16, 2004 6:53 pm
by RUFF
ISUZUROVER wrote:What is the rest of the CV like???
Star is intact.
Yes its a longfield that is aprox 10 hrs old at the most out of the Lockless Monster.
Posted: Wed Mar 24, 2004 10:30 pm
by DiscoDino
Landy Man...
So what's the news on the front?
Posted: Thu Mar 25, 2004 4:12 pm
by mickrangie
The biatch moves once again!!!
I'll let landyman explain the finer details.... and post some pics
Posted: Thu Mar 25, 2004 5:18 pm
by landy_man
yep she drives...
will post pics soon
Posted: Thu Apr 01, 2004 8:13 pm
by DiscoDino
"soon"
Well, I hope your excuse is that you're wheeling the HELL out of it, if any other:
Seriously...I gotta know if I can go hi-pinion in the front or not?!?!?
Posted: Thu Apr 01, 2004 8:46 pm
by landy_man
yeah sorry dude
been super busy...
you will have to go high pinion in the front
low does not fit.
Posted: Sat Apr 03, 2004 12:32 am
by DiscoDino
Landy_man,
Thanks for the input: Hi-Pin it is
Just a small tech Q:
Do you have to change anything for the Toy pinion to adapt to the Rover driveshaft?
Are you suing JM 3rds or re-drilled Toy ones?
Thanks
nadim
Posted: Sat Apr 03, 2004 12:05 pm
by mickrangie
DiscoDino wrote:Landy_man,
Thanks for the input: Hi-Pin it is
Just a small tech Q:
Do you have to change anything for the Toy pinion to adapt to the Rover driveshaft?
Are you suing JM 3rds or re-drilled Toy ones?
Thanks
nadim
the toy flange is round so we off set the the rangie flange and re drilled it we are going to have to grind the inner ring of the LR flange it sits it flush...
good luck in finding a Hi Pinon diff in any thing other then 4.11 (from 80 series) we had a hell of a time and we wanted 4.8 but could only find 4.5 or 4.11 so LandyMan changed the rear diff to suit the front diff... i didn't want him too cause 4.5 in the front and 4.8 in the back would be cool to watch... BANG!!!
HTH
Posted: Sat Apr 03, 2004 3:03 pm
by HSV Rangie
what I diid was to machine the toy flange to take the rover shaft.
Machine the centre to the toy diam and out to the toy size.
Drill the toy falnge to take the RR drive shaft.
Hps available in 4.1, 4.3, 4.5, and a few others.
Michael.