Notice: We request that you don't just set up a new account at this time if you are a previous user. If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
waxen wrote:We had had similar problems to this and after a lot of head scratching the locker was removed, checked ,o rings replaced, checked again, refitted...........In short no problem could be found. But the intermittent problem was still there.
The locker was removed again, this time it was coaxed into misbehaving on the bench, by loosening the seal ring and realigning it, (this was because it had moved itself) every now and again after the centre was rotated it would leak. The journals etc were checked for runout, the seal ring was ok too, but a new seal ring was put in anyway, the id of the new ring was a couple of 'thou larger than the old one and so far it has not leaked again.
In summary the conclusion was that the combined sum of tolerance limits with that collection of parts was the problem. Anyway it may give you a starting point.
Cheers
What a variance in a QUALITY CNC MACHINED UNIT but 4X4 guy told us all that this is impossible! ARB ARE THE ONLY SHIT HE SAID
sounds like you all have been had . YOU ALL must have cheap chineese copies
Might keep my CNC machined lockright at least it works $199 us
It must be a fault in the locker .. not the O-Ring that are churned out by the million from some factory in china useing recycled condoms as the raw material.
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
What arb using chinese O rings now??
ok im not saying that arb lockers are shit at all
they do have the best rep in the business but like everone they too have their problems.
if I could justify the cost on a purely off road car id probably run them myself.
what im saying is that 4X4 guy is just an over the top wanker who's obviously full of bullshit and im pretty sure he doent know what CNC machining even is.
He should form an opinion on a product by himself not by reading the back of the box it came in.
85 high roof 1.3, 6.5 tc, air lockers,ruf and 34 swampers. yep its an ugly pos.
has wrecking ball actually gotten back to us about his problem and what he has found? or are we just sitting here comparing penis size? AJSR and 4x4 GUY need to get a hotel room and resolve some tension.
lwb 1.6efi,4sp auto,f&r airlockers,dual t/cases.custom coils.builder of ROAD LEGAL custom suzukis...and other stuff.
CAD modelling-TECH drawings-DXF preparation.
http://www.auszookers.com/index.php
joeblow wrote:has wrecking ball actually gotten back to us about his problem and what he has found? or are we just sitting here comparing Pencil size? AJSR and 4x4 GUY need to get a hotel room and resolve some tension.
sorry joe got carried away
85 high roof 1.3, 6.5 tc, air lockers,ruf and 34 swampers. yep its an ugly pos.
thats cool, no need to appologise. just curious as to what he has found so this thing can start all over again, i'm sure we are looking forward to that
lwb 1.6efi,4sp auto,f&r airlockers,dual t/cases.custom coils.builder of ROAD LEGAL custom suzukis...and other stuff.
CAD modelling-TECH drawings-DXF preparation.
http://www.auszookers.com/index.php
sorry guys i'd forgotten about this thread . i did take it back to the installer and they fixed it no worries .
i think from memory the o ring was to tight . its been working good ever since