Outer Limits 4x4 Board

Posted: **Sat Jun 13, 2009 9:01 pm**

Im only new to this forum but i would be keen on a set for a D2 30%.

Posted: **Sun Jun 14, 2009 12:43 pm**

Strange Rover wrote:Sombody should ring Chuck and convince him he will need them in his rangie..that would be your 10th.

Sam

Already tried...but you know what Chuck is like. He thinks that his Rangie on 36" tyres will be fine with standard gearing.

Posted: **Mon Jun 15, 2009 9:26 am**

Micka 49%
Grimace 49%
Goldrover 49%
jbell 49%
DARTHrover 49%
halfshaft 30%
isuzurover 30%
revor 2x ???
Matman 30%

Posted: **Mon Jun 15, 2009 12:22 pm**

im out...
sorry guys, bigger fish to fry.

Micka 49%
Grimace 49%
Goldrover 49%
jbell 49%

halfshaft 30%
isuzurover 30%
revor 2x ???
Matman 30%

Posted: **Wed Jun 17, 2009 9:49 am**

Isnt Harley keen for a set Micka???

Posted: **Wed Jun 17, 2009 11:49 am**

I'm a late starter but a definate for 30% gears.
Cashed up ready to go.
Hope i'm not too late.

paul@busby.com

Cheers Buzz

Posted: **Wed Jun 17, 2009 12:58 pm**

So that makes:

Micka 49%
Grimace 49%
Goldrover 49%
jbell 49%
halfshaft 30%
isuzurover 30%
revor 2x ???
Matman 30%
buzz66 30%

That makes 10!

Posted: **Thu Jun 18, 2009 3:56 pm**

My transfer case is out & I'm starting to strip it. I will be getting a set next week. I would like to do it as part of the group buy but will getting a set either way.
cheers
Phil

Posted: **Mon Jun 22, 2009 10:32 am**

Now that there is 10 people, are we going to make deposits to MR for the gear sets to lock in the orders or how is it going to work?

I'm not in any rush but I want to get my VC out and the modded LT 230 in by the end of next month if possible.

Cheers Buzz

Posted: **Mon Jun 22, 2009 4:08 pm**

Email sent to Warren today after speaking with him.

Will post up his reply for all to see.

Posted: **Mon Jun 29, 2009 3:08 pm**

Reply from Warren...

Michael,
Sorry the price has to remain the same.
As we spoke last time, if your blokes want to go ahead, just let me know .
They can send us some deposit ( say $500 ) and their intermediate gear.
It would help if they send their low range gear as well.
We need that so we can be sure what dog teeth the gears have (ie wide or narrow)

Warren

Posted: **Mon Jun 29, 2009 4:23 pm**

Thanks Micka,

So to clarify, price is $1265 INC GST?

Posted: **Mon Jun 29, 2009 5:09 pm**

ISUZUROVER wrote:Thanks Micka,

So to clarify, price is $1265 INC GST?

Correct.

Posted: **Mon Jun 29, 2009 7:16 pm**

So ive got to pull out my transfer case gears and send it to them to be sure what dog teeth the gears have?

Posted: **Mon Jun 29, 2009 8:27 pm**

Matman wrote:So ive got to pull out my transfer case gears and send it to them to be sure what dog teeth the gears have?

AFAIK the intermediate gear needs to be modded - so it has to be sent to them.

Micka, have they told you what the turnaround time is?

Posted: **Mon Jun 29, 2009 8:31 pm**

ISUZUROVER wrote:
Matman wrote:So ive got to pull out my transfer case gears and send it to them to be sure what dog teeth the gears have?
AFAIK the intermediate gear needs to be modded - so it has to be sent to them.

Micka, have they told you what the turnaround time is?

So i might have to get another intermediate gear then as i cant take out mine as i need to get to work and im to ugly to hitch.Would anyone have a spare one i could buy?

Posted: **Tue Jun 30, 2009 7:35 pm**

Im sorry guys but as of next week im working for Rudd thanks to cutbacks on the RTA so im out.

Posted: **Thu Jul 02, 2009 10:56 am**

Is the deal done on the Maxi-Drive gears?
If not:
Any idea how much to ship to the States?
Could I just buy the gears and install them later without tearing down my t-case now or do the gear mods need a special machining.
I'm new to the forum and was drawn from the D90 list because I need to either lower my RRC diff gear ratios or use the T-case mod and that has some advantages.
Thanks,

Clark

Posted: **Thu Jul 02, 2009 11:23 am**

CDB wrote:Is the deal done on the Maxi-Drive gears?
If not:
Any idea how much to ship to the States?
Could I just buy the gears and install them later without tearing down my t-case now or do the gear mods need a special machining.
I'm new to the forum and was drawn from the D90 list because I need to either lower my RRC diff gear ratios or use the T-case mod and that has some advantages.
Thanks,

Clark

From page 3

red90 wrote:
HI JACK wrote:Yes you can get them now and put them in your case later

H
Only if you want to buy another intermediate gear. The "normal" method is to remove your intermediate gear and send it to them for modification.

So if you buy an intermediate gear and measure the dog teeth on your low range gear then that should be fine.

Posted: **Thu Jul 02, 2009 1:15 pm**

[So if you buy an intermediate gear and measure the dog teeth on your low range gear then that should be fine.[/quote]

Can I measure the dog teeth if I pull the t-case pan.
Does "measure" mean count the teeth?
Is the intermediate gear mod included in the price for the group buy.
Sorry for all the questions - I'm a tinkerer not a mechanic.

Clark

Posted: **Fri Jul 03, 2009 9:47 pm**

Sorry guys i should have searched but hay here goes.
What is the best way to find out what high range gearing your case has?
I have 2 LTs in the shed that are pulled down ready to rebuild and they both have a diffrent shaft and bearing setup to support the intermediat gear.
I have no idea what vehicle they came from.
Cheers Nottie

Posted: **Fri Jul 03, 2009 9:58 pm**

nottie wrote:Sorry guys i should have searched but hay here goes.
What is the best way to find out what high range gearing your case has?
I have 2 LTs in the shed that are pulled down ready to rebuild and they both have a diffrent shaft and bearing setup to support the intermediat gear.
I have no idea what vehicle they came from.
Cheers Nottie

Maybe one is from a defer and the other from a disco or rangie, i'm pretty shore the defender ones have lower gearing, not shore if there is any difference between the rangie and disco though.

TIM.

Posted: **Fri Jul 03, 2009 10:20 pm**

Cheers Tim
All sorted as i found this on Ashcrofts site
http://www.ashcroft-transmissions.co.uk/part_8.html#pa1
Has all the suffix and gearings on it.
It seems that one of the boxes is an early roller bearing type (needle roller)

CDB you should be able to work out your gearing of your case as so you get the right set done.

Cheers Nottie

EDIT click on technical facts near the bottom of the page.

Posted: **Tue Jul 07, 2009 10:50 am**

Will the group buy Maxi-Drive gearset work in a 1.667 t-case?
It sounds like it is different than the 1.4 or 1.2 t-case gearsets.
Thanks for your response

Posted: **Tue Jul 07, 2009 9:02 pm**

I rang MR Automotive yesterday. They are waiting for all concerned to make a $ 500 deposit to lock this deal in.

As of today I'm the only one to make a deposit.

MR quoted me quite a good price even if this package deal doesn't work out.

Either want it or you don't...so cough up you bastards

Posted: **Tue Jul 07, 2009 11:50 pm**

whats the contact details for sending the deposit ?

Jeff

Posted: **Wed Jul 08, 2009 12:00 am**

jbell wrote:whats the contact details for sending the deposit ?

Jeff

Our contact details

Phone: (07) 3284 6688

Fax: (07) 3883 1485

Email: mrauto@oznetcom.com.au

Address:
182 Anzac Avenue, Redcliffe, Queensland 4020, Australia

Opening Hours:
Monday - Friday 8am to 5pm
Saturday 8:30am to 11am

I will be calling them tomorrow. I am happy to share freight with any WAers.

Posted: **Wed Jul 08, 2009 12:18 pm**

Just called. Warren is the guy organising it at MR and he is not there today. Will be back tomorrow.

Posted: **Wed Jul 08, 2009 2:10 pm**

Warrens Direct Email Address is

warren@mrauto.com.au

Posted: **Wed Jul 08, 2009 9:07 pm**

Yeh Ben I would be keen to freight together to try to
keep the cost down.. just got to pull it out 1st.

Jeff

Outer Limits 4x4 Board

Group Buy: Maxi Xfer Gears **HOLY FARK - THERE'S 10**

Group Buy: Maxi Xfer Gears HOLY FARK - THERE'S 10