Outer Limits 4x4 Board

Panhard bushes
55135-01J01 top (small hole)
55135-01J10 bottom (large hole)

Guys Have a 89 mav SWB just rang nissan to get the panhard rod bushes for the front using these # above they rekn i have to buy the whole rod .

Anyway can some1 please tell me if they are the right part # for a 89 SWB front panhard rod and how much they cost please?

Also are they a press in fit and is it 1 bush per end or 2 im used to the toyota havin 2ea end .

Thanks Dave

I don't suspose anyone would know the part number for the circlip that goes on the cv before the free wheeling hub on a GU 2.8 patrol? Nissan are telling me theres about 6 different circlip sizes.

Cheers Mick.

Yes there are 6 types 1.1mm to 2.1mm. you should measure the end play on the shaft and order to suit. But if you are like me just go for somewhere in the middle 1.5mm 39253-01j02.

The desk jockeys at nissan literally know absolutely nothing, alot of them barely know how to look things up using the computer - a retarded drooling psycotic monkey with no arms could in most cases do a better job.

The idea of you not being able to just use those bushes is ridiculous, it is a scam on their part. It is due to the nissan shimmy that develops, in a lot of cases it is worn front panhard bushes that is the cause of the problem. A quick and "profitable" fix for them is to sell you a complete front panhard rod with new bushes...

Just walk in order and pay for 2x small hole and 2x large hole, rip your panhards off and press these in. Obviously taking note where the large/small wholes need to go..

Edit: might vent some more parts anger. Sort of like when I went to repco to buy a spare wheel cover for my old mans pajero. The guy wanted/needed the VIN chassis number to supply me with a f#$king wheel cover. like wtf !!! Spastics

SHIFTY wrote:Yes there are 6 types 1.1mm to 2.1mm. you should measure the end play on the shaft and order to suit. But if you are like me just go for somewhere in the middle 1.5mm 39253-01j02.

Thanks mate 1.5mm sounds like close enough.

Cheers Mick.

from another thread

I have 2 part numbers for the same filter. The Nissan genuine part is actually a bosch part with a Nissan sticker over the Bosch Sticker.

Nissan Part Number is 14371-R8025A
Bosch Part Number is 14612501016N1

Getting the Bosch part is about 1/2 the price of the Nissan part.
Just go to an injector service centre

i got a couple here.

GQ patrol exhaust manifold gasket TB42 14036-03J00
GQ Oil Seal for back of transfer behind handbrake 33142-01J01
GQ rear axle oil seal 43252-C6001
Gq transfer front pinion oil seal 33216-01J00

on another note, mods, can we make this a sticky????

Can anyone hook me up with one of those cd's? Just PM me and I'll PM you my address

Thanks
Glenn

are the fast cd's still doing the rounds? if anyone could copy one for me i'll send the postage + fee. thanks

Wasn't the idea that after you receive cd you burn 5 copies so eventually we all have one?

PM me pls, that cd would be very handy

after reading the original thread it appears the intention was to get one burn five and pass it on, but i figure its died a natural death, so i will pay someone for a copy.

ausoops wrote:are the fast cd's still doing the rounds? if anyone could copy one for me i'll send the postage + fee. thanks

anyone??

hey i know im late but this sounds like the bees knees anyone in perth got this so i could grab a copy or anyone willing to post it if i send over cost of postage and copying?
cheers

GU lockwasher conversioN for GQ Front wheel bearings.

NI-40262-02J00 1 PER SIDE - NUT LOCK, FRONT WHEEL $8
NI-40264-02J10 1 PER SIDE - WASHER, FRONT WHEEL BEA RING $6
NI-01414-00051 2 PER SIDE - BOLTS $1.50ea

i work for nissan so im more than happy to post part numbers for people if they are needing any!

revn211 wrote:i work for nissan so im more than happy to post part numbers for people if they are needing any!

Get busy then Mr..

Partnumbers for the rearwall in GQ and GU Ute´s ... need em because the local Nissan dealer is absolutly useless ...

This is a great thread, so lets keep it goin.

Revn211, I will be contacting you in the future, I am sure. The parts guys in Canada all give me blank stares when I say Nissan Safari / Patrol. However, after doing a lot of cross reference work (if I can get a Nissan number to start with) I have been able to find some parts.

If anybody still has a copy of the parts DVD or CDs and would be willing to make a copy and post it to Canada, I would be happy to do 5 copies for the Safari owners here and re-imburse your costs. Just PM me. Cheers,

John

pm sent canuck

Hobbz wrote:Partnumbers for the rearwall in GQ and GU Ute´s ... need em because the local Nissan dealer is absolutly useless ...

if your referring the the rear most panel of the cab where the rear window sits the part numbers are
791001Y430 (GU)
7910010J30 (GQ Before 91)
7910039J31 (GQ After 91)

Thanks

TD42 Hitachi 60A Alternator parts.

Purchased from Ashdown's in Sandown (Vic).

Brushes: Part No. 22-71501 <$10
Rectifier / Regulator no longer available.

Same day courier to Metro Melbourne. $9.75.

Parts were in stock at the time of my call and order.

Rear pinion seal:

38183-c7123

BTT.
anyone got any to add?

I've been collecting from here and other forums and put them in a bit of an order.

www.downunder4x4.net/forum/showthread.php?t=7417

I still have alot more to add but i'm getting there.

Cheers Mick.

Hey all

Anyone be able to tell me what the part number is on a GQ 4.11 diff centre? there is a part number on the crown wheel but still not sure if its a 4.11 centre.

Cheers

it will have the ratio on it, eg 37:9 is a 4.11111111111111 diff

Anyone got the part no. for the sector shaft from a GQ steering box? Or where I might find one?

[quote]it will have the ratio on it, eg 37:9 is a 4.11111111111111 diff[quote]



thanks for that mate :-)

anymore.???