Page 1 of 1
Air solenoids - Not for lockers
Posted: Sun Apr 29, 2007 7:11 pm
by mickyd555
I am planning on running two air tanks that will cut out at different pressures. One small one for lockers and the other for air tools, tyres and anything else. I am just giing to have two different pressure switchwes for the two tanks and have them control an air solenoid.
Is there anything out there readily available with 12V control that anyone can suggest?
Alternatively, am i going too far and will i be able to use one tank, and will the standard 90-130Psi switch be fine for lockers and air tools??
Posted: Sun Apr 29, 2007 7:17 pm
by ratboy
gas lockoff ????
Posted: Sun Apr 29, 2007 7:19 pm
by mickyd555
ratboy wrote:gas lockoff ????
Im a sparky not a plumber. i assume its a safety thing on gas appliance??
I would need a normally closed solenoid for fail safe so i dont lose all air if something goes wrong.
Re: Air solenoids - Not for lockers
Posted: Sun Apr 29, 2007 7:21 pm
by ausyota
mickyd555 wrote:Alternatively, am i going too far and will i be able to use one tank, and will the standard 90-130Psi switch be fine for lockers and air tools??
Run one tank at 130 ish psi and use a pressure regulator to regulate it down to 90psi for the manifold that the air locker solinoids are on.
Posted: Sun Apr 29, 2007 7:22 pm
by Mulisha
mickyd555 wrote:ratboy wrote:gas lockoff ????
Im a sparky not a plumber. i assume its a safety thing on gas appliance??
I would need a normally closed solenoid for fail safe so i dont lose all air if something goes wrong.
I think his talking about a LPG lock off valve..
Re: Air solenoids - Not for lockers
Posted: Sun Apr 29, 2007 7:23 pm
by mickyd555
ausyota wrote:mickyd555 wrote:Alternatively, am i going too far and will i be able to use one tank, and will the standard 90-130Psi switch be fine for lockers and air tools??
Run one tank at 130 ish psi and use a pressure regulator to regulate it down to 90psi for the manifold that the air locker solinoids are on.
more info on this please as that would solve all problems!!
Posted: Sun Apr 29, 2007 7:24 pm
by ratboy
ok lpg lockoff it may do the job just worth looking at
Posted: Sun Apr 29, 2007 7:30 pm
by Mulisha
GRA sell lockoffs...
Right at the bottom of the page
http://www.gasresearch.com.au/
Rick.
Re: Air solenoids - Not for lockers
Posted: Sun Apr 29, 2007 7:40 pm
by ausyota
mickyd555 wrote:ausyota wrote:mickyd555 wrote:Alternatively, am i going too far and will i be able to use one tank, and will the standard 90-130Psi switch be fine for lockers and air tools??
Run one tank at 130 ish psi and use a pressure regulator to regulate it down to 90psi for the manifold that the air locker solinoids are on.
more info on this please as that would solve all problems!!
Well you run your 130 psi pressure switch on your pump and this fills the tank to 130psi (you still with me
)
You then get a pressure regulator like used when spray painting that has a big knob that you can turn to adjust the output pressure. Set this to aprox 90psi and run an air line to a manifold that your airlocker solinoids are screwed into.
Posted: Sun Apr 29, 2007 7:45 pm
by MissDrew
It'll be fine and anything else you do will be a waste of time and money.
Posted: Sun Apr 29, 2007 7:52 pm
by jet-6
Micky since your a sparky(same here) get yourself a pressure switch from a pressure pump(water) or best of all go buy yourself one of those $100 compressors from supercrap and retro fit/wire all the gear over, damn you can even use the tank itself!
Thats what im going to be doing anyway
Posted: Sun Apr 29, 2007 8:50 pm
by dai-hard
try here
http://www.metalwork.it/eng/elettrovalvole.html we use heaps of 12/24v soleniods at work . not cheap though.
Posted: Mon Apr 30, 2007 7:27 am
by bru21
this is what regulators are designed for! they cost $40 and will give a pretty constant pressure regardless of tank pressure (as long as its above 90). Fit a one way valve if you are worries the main tank will go below 90 psi.
Posted: Mon Apr 30, 2007 7:49 am
by Dagger82
would a regulator mounted in a vehicle handle all the vibrations and such of driving around???
Posted: Mon Apr 30, 2007 8:31 am
by Shadow
the solenoids you find on airhorns would probably work, they operate up to 150psi, are normally closed, and can be found on ebay (hornsales or something is a aus seller that had them at one stage)
Posted: Mon Apr 30, 2007 8:49 am
by Jimmu
If a regulator can handle the vibrations when it is strapped to a compressor I am sure it will handle the vibrations on a 4wd
Jimmy
Posted: Mon Apr 30, 2007 9:00 am
by DNA Off Road
Dagger82 wrote:would a regulator mounted in a vehicle handle all the vibrations and such of driving around???
Mine do..
Cheers
Posted: Mon Apr 30, 2007 12:36 pm
by mickyd555
Guts wrote:It'll be fine and anything else you do will be a waste of time and money.
thankyou, exactly what i needed