Is it a hard task??????
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
MK Shortie Body Lift
MK Shortie Body Lift
I was wondering if anyone has done a 2 inch lift on a MQ/K shortie and what size bolts do i need to complete this task????????
Is it a hard task??????
Is it a hard task??????
My mate and I did a 2 inch body lift on his mq shortie. It was a very easy task. It was a half day job including making the body lift blocks (steel) and buying the bolts!
From memory (it was a while ago) there are 10 bolts (5 a side). They are all the same length except the rear two. I can't exactly remember what size they were but I can find out. The difference with the rear was they had captive nuts in the body, therefore we needed to get exactly the same size thread on a two inch longer bolt.
Radiator didn't need repositioning. The fuel filler hose could have been extended a little, but it stretched just enough (there was a minor leak). I believe he had to pop the low range rubber boot out cause 4wd low didn't engage properly cause it was hitting the body. I think he may have cut a bit from the floor though (not 100% sure).
Also, we released the clutch fixed pipework from the body so the coil could stretch as we lifted the body. There is just enough excess length on the flexible clutch line to the slave cylinder.
I think we were able to stretch the air intake pipework fromt the filters just enough.
Other than that, i think it was all good. I'm sure I'll be corrected by mq080 if I'm wrong.
From memory (it was a while ago) there are 10 bolts (5 a side). They are all the same length except the rear two. I can't exactly remember what size they were but I can find out. The difference with the rear was they had captive nuts in the body, therefore we needed to get exactly the same size thread on a two inch longer bolt.
Radiator didn't need repositioning. The fuel filler hose could have been extended a little, but it stretched just enough (there was a minor leak). I believe he had to pop the low range rubber boot out cause 4wd low didn't engage properly cause it was hitting the body. I think he may have cut a bit from the floor though (not 100% sure).
Also, we released the clutch fixed pipework from the body so the coil could stretch as we lifted the body. There is just enough excess length on the flexible clutch line to the slave cylinder.
I think we were able to stretch the air intake pipework fromt the filters just enough.
Other than that, i think it was all good. I'm sure I'll be corrected by mq080 if I'm wrong.
If you want a spare 60 for bits-
http://carl.outerlimits4x4.com/viewtopic.php?p=1109227#1109227
http://carl.outerlimits4x4.com/viewtopic.php?p=1109227#1109227
mate, the lift is easy!!!!
Look at Heathx4's thread in the members section he has done a body lift recently and is happy. Mine took half a day and was simple enough except for the rear 2 bolts.
With regaurds to the length of the bolts, just take one of the middle ones out and get some that are how eva many inches longer.
if u want to know more drop me a PM
cheers
screwy
Look at Heathx4's thread in the members section he has done a body lift recently and is happy. Mine took half a day and was simple enough except for the rear 2 bolts.
With regaurds to the length of the bolts, just take one of the middle ones out and get some that are how eva many inches longer.
if u want to know more drop me a PM
cheers
screwy
TUFF TRUCK TEAM OPPOSITE LOCK Proudly Sponsored By:
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Who is online
Users browsing this forum: No registered users and 0 guests