Page 1 of 1

altering an intercooler

Posted: Mon May 04, 2009 6:23 pm
by GU-ish
hey all
i have an intercooler similar to the one in the first pic and want to know if it is possible to get it altered so it is like the one in the second pic. ie. the inlet/ outlet been altered.
can it be done?
where abouts will do it?
somewhere around hoppers crossing or werribee would be handy (vic)

Image

Image

Posted: Mon May 04, 2009 6:45 pm
by kond
Cheaper to buy a new one mate

Posted: Mon May 04, 2009 7:11 pm
by nastytroll
Any ally fab shop can do it.

I'm not sure location wise but ask awill4x4, he's the resident TIG master. He is in Vic some where.

Posted: Mon May 04, 2009 7:16 pm
by GU-ish
mite have to have a look in yellow pages then... or if any1 knows somewhere and would recomend let me know

Posted: Mon May 04, 2009 7:57 pm
by 80's_delirious
kond wrote:Cheaper to buy a new one mate
yeah coz the one above is obviously off the shelf and hasnt been cut and shut at all :roll:

try some ally fabrication shops, a carton would probably get it done ;)

Posted: Mon May 04, 2009 8:45 pm
by chpd80
Could you simply put a 90 degree silicon elbow on it to get the outlet pointing down???

Posted: Mon May 04, 2009 8:54 pm
by bogged
CALLING AWILL4X4....
Andrew is making the Laminova Intercoolers on here.. if it can be done ask him.. hes in Carrum Downs.

Posted: Mon May 04, 2009 9:26 pm
by GU-ish
chpd80 wrote:Could you simply put a 90 degree silicon elbow on it to get the outlet pointing down???

its for a top mount cooler, so it needs to be a 180 degree bend but that will take up alot of room, that is why i want it pointing down so i can then use a 90 degree bend to shoot back under it and into the intake manifold.

Posted: Tue May 05, 2009 9:01 am
by oondy
Considering that pic is from my website, why wouldn't you ask me to mod it?

or save some $$ and buy a complete kit in the first place.

cheers

OONDY

Posted: Tue May 05, 2009 4:28 pm
by KYSI
oondy wrote:Considering that pic is from my website, why wouldn't you ask me to mod it?

or save some $$ and buy a complete kit in the first place.

cheers

OONDY
He is in melbourne

Posted: Tue May 05, 2009 5:01 pm
by PJ.zook
I recommend Race Radiators at Bennet St Dandenong. They mod and/or repair our truck 'coolers for work, do a nice job.

Posted: Tue May 05, 2009 5:06 pm
by cj
bogged wrote:CALLING AWILL4X4....
Andrew is making the Laminova Intercoolers on here.. if it can be done ask him.. hes in Carrum Downs.
He modded my air/water for me in a number of ways including relocating the outlet and changing the size of the inlets and outlets and ..... :armsup:

Posted: Tue May 05, 2009 6:18 pm
by bogged
cj wrote:
bogged wrote:CALLING AWILL4X4....
Andrew is making the Laminova Intercoolers on here.. if it can be done ask him.. hes in Carrum Downs.
He modded my air/water for me in a number of ways including relocating the outlet and changing the size of the inlets and outlets and ..... :armsup:
He is god.. :armsup:

Posted: Tue May 05, 2009 6:21 pm
by GU-ish
bogged wrote:
cj wrote:
bogged wrote:CALLING AWILL4X4....
Andrew is making the Laminova Intercoolers on here.. if it can be done ask him.. hes in Carrum Downs.
He modded my air/water for me in a number of ways including relocating the outlet and changing the size of the inlets and outlets and ..... :armsup:
He is god.. :armsup:
better PM god then.

Posted: Tue May 05, 2009 7:47 pm
by fester2au
Couldn't be easier - holesaw a new hole in correct location, cut away anything of the inlet that the holesaw didn't remove and blend the shape of a short straight piece of pipe intot he new spot and weld away.

If you can't get ahold of AWILL jump in the phone book and ring a few sheetmetal shops to find one that does ally work.

If it cost you more than $60 I'd be surprised.