Outer Limits 4x4 Board

Not getting many answers on Snake so reposting. Can someone tell me how much is a reasonable price for:
a. Reco'd Sierra 1.3L transfer case
b. Vitara 1.6L EFI engine, gearbox and transfer case

Thanks in advance.

About $250 - $300 for a good 2nd hand xfer case.
Full reco xfer case is over $800 (retail)
You'd be looking at around $2500 for a Vitara 1.6EFI + tranny + xfer

I've got an average xfer case here at home if you are interested.

damo's got the pricing spot on. OUCH!!!....ROTFL

While we are at it I'm chasing an 1.3 engine gearbox and transfer.
I am rushing to try and get my new truck within the next 4 weeks and try and compete in Queensland.
Condition doesn't matter the cheaper the better.
Thanks

Hey Sam
we gunna c any spy pics of your new rig or wat its all tubular isnt it:mad: ?

I will post some pics when i figure out how to attach them.
It doesn't look like much yet as all I have are to bare chassis rails.
I am still using a Zook chassis but it has been chopped off directly under the seat.I f you saw my old car the chassis ends where my 1/4 elliptic springs started.I started doing the tube work today but when I found out about the XRCC I decided to try and get the truck finished and enter.I think I'm pushing s--t uphill but it's worth a try. I have to try and keep the big rigs honest.

Sweet mate sounds sik
N if it looks as mad as your last effort its gunna be awesome , leaf all u gunna go coils

It will1/4 elliptic in the rear
Spring over in the front using mazda springs.
Vitara diff in the rear
vitara with dana knuckles in the front
37 mtr's
The new truck is going to be both bullet proof and hopefully 10 times better built than the last one as it was the test bed for the new one.
Sam

Sam why run Zook diffs why not use hilux or D44s???

I am using dana 44 knuckles and axles in the front. I chose to use Vitara diffs because.5.12 ratio standard. More clearance than hilux and dana.Lastly cheaper.
I am trying to build a competitve truck that maybe one day market as a complete buggy as you can buy in the States but at a reasonably cost.

Yeah thats fair enough i guess. Well i hope you get it up and running and get it up here as we need some more competition here. Should be a good event there is defianatly some good rock where they are holding it.

I will try for the first round but i think it is unlikely but I will defenately be there for the rounds next year.

Just enter, then bring it up here and shit loads of steel and we can finish it of up at the comp.

As long as it goes, bolt some spookie panels on and there you have it, pupose built rock rig.

I dont drive a zuk but think there awesome when built correctly.

It seems the yankies are all going feather weight rigs.

If you dont get it finished in time come up and check it out anyway.

sam,

check out the for sale section dude. I've got a bucket load of parts I wanna get rid of.

give me a call on 0405109571 afterhours if you are interested.
camski also has my icq and msn details if you'd prefer to chat over those.

Hey Sam,

Your plan sounds good. Bozook was a weapon, this is gonna be even better. I've found a '84 Sierra in good nick with a locked up xcase. The engine has only done 107000kms and the only thing wrong is the transfer is stuck in neutral. The old dude that owns it don't wanna pay the cost that was quoted to him to fix it up. I'm seriously thinking about getting this and putting the Vitara mechanicals in it. If I do, the engine and gear box is up for sale and I reckon it might fit the bill as to what you want. It'll offset the cost of putting the Vitara stuff in for me. Can you email me on tranhtn @ yahoo.com.au if you're interested? Thanks.

Nam

Nam, how much is the old guy selling the zook for????????

That problem with the xfer case is prolly just the shifter "sheet". Same thing happened to my first SWB. It costs about $15 in parts to fix and a bit of your time. This is the most likely situation, but of course the case could be buggered. In any case it's not hard to fix, just get a 2nd hand xfer case.

Nam, before you coughing up for another transfer, check it's not the plastic seal sheet under the transfer case shifter. ( it's only a cheap part)

Is there anyone else entering XRCC?

We know Overkill is trying to get his rig ready, i'm in the same boat pulling out the stops to get mine done.

Anyone else?????

ive had to fix three of those POS in my life, and i end up ringing up stoners, that know that drive that junk

they come through my work and are stuck in L4x4

they always seem nice enough people though, and the stockers, are UNREAL

bj on roids wrote:they always seem nice enough people though

As opposed to the wankers that drive cruisers eh BJ?

mainly the tossers, drive stockers, and they drive EVERYTHING from patrols, to suzukis and everything in between like hiluxes and stuff, they are all, yeah, i wanna take it to ARB, and get ass raped

I can't believe I am going to do this, but I am going to defend ARB! They only raped me a little bit on the lockers for my truck (compared to major fistworthy ass-raping on the lockers for my last truck) And.. wait for it.. They lent me some tools a couple of weeks ago free of charge!!

dont get me wrong ARILOCKERS are AWESOME

:(
although, serioously if you are nice to the lockers, they are a GREAT product

Hey Sam, I thought you were gonna go coilovers for the new project...

Cam

right or wrong my zuk will be there hopefully with injected v8 installed only time will tell

v8 in a zuk ... should be good for wheels stands!

I bet crispy's hyundai Terrican v6 could beat IT

wtf is this thread doing back up here?

N*A*M wrote:wtf is this thread doing back up here?

Apparently there is a teracan owned by this crisp fellow that has something to do with Everything on this BB

suzi 90 model 1.3 engine/gearbox/radiator/starter/alt + all acc the lot $600. can test drive in car n transfer/case $300
or if u can get a bundy front diff complete or 80s front diff complete. id do a clean swap.