Page 1 of 1
[b]Denco over standard, worth it?[/b]
Posted: Tue Aug 04, 2009 11:17 am
by JenoNT
G'day chaps, new to the forum, let me say, I love your work!
Got a GU 4.2 factory turbo with a 3 inch zaust and dump pipe, goes quite well.
Was looking at intercoolers and have a question I'm hoping someone can help me with. How much extra go will replacing the factory nissan turbo with the Shwitzer get me?
See options are, just do the intercooler, or go the whole hog and replace the turbo and add the intercooler to match. Question is, is it worth it? Or is just adding the intercooler better value for money.
Appreciate any comments from those that have travelled the same route.
Cheers, Jeno in Darwin
Posted: Tue Aug 04, 2009 11:50 am
by coxy321
What sort of budget are you looking at??
Many, many,many options out there regarding turbos and intercoolers....
Re: [b]Denco over standard, worth it?[/b]
Posted: Tue Aug 04, 2009 1:31 pm
by bogged
Is it worth it? To some people yes.. it comes down to expectations. To some people no it isnt.
But before that I'd plan what you want out of it.. 200rwkw, 900Nm, etc etc
Then talk to people in the know on how to get to that position.
I'd be lookin at a garrett.
Posted: Tue Aug 04, 2009 5:40 pm
by GutSquisher Media
Was given this by Denco when they did my Troll. They where putting a upgrade kit together for TD42T's
From what I understand it was a replacement turbo and intercooler. Best to ring them to find out what is in the kit.
Posted: Tue Aug 04, 2009 5:45 pm
by marin
ummm wtf?
Why measure (calculate) the power at the engine, but measure the torque at the wheels?
Posted: Tue Aug 04, 2009 7:14 pm
by coxy321
Ben i'd say that by those numbers it is RWKW, not FWKW.
Jeno, if your not super-fussed about dollars, i'd go a Garrett GT2860RS ball bearing turbo, and a Laminova cored w/a intercooler, and if you have some more coin available - get pump mods done too.
Should prove to be quite an improvement from your current setup.
Posted: Tue Aug 04, 2009 9:41 pm
by bogged
coxy321 wrote:Ben i'd say that by those numbers it is RWKW, not FWKW.
Jeno, if your not super-fussed about dollars, i'd go a Garrett GT2860RS ball bearing turbo, and a Laminova cored w/a intercooler, and if you have some more coin available - get pump mods done too.
Should prove to be quite an improvement from your current setup.
Yea, I'd agree with all that.. should get it done for $8-10k all up and have some decent power.
Or chuck a V8 in it.
Posted: Wed Aug 05, 2009 12:40 am
by matt.mcinnes
Marin's TD42T GQ manual
DTS turbo kit in Blue and in Red with one of our intercoolers added.
More info here.
http://www.outerlimits4x4.com/ftopic164122.php
Posted: Wed Aug 05, 2009 9:56 am
by jessie928
bogged wrote:coxy321 wrote:Ben i'd say that by those numbers it is RWKW, not FWKW.
Jeno, if your not super-fussed about dollars, i'd go a Garrett GT2860RS ball bearing turbo, and a Laminova cored w/a intercooler, and if you have some more coin available - get pump mods done too.
Should prove to be quite an improvement from your current setup.
Yea, I'd agree with all that.. should get it done for $8-10k all up and have some decent power.
Or chuck a V8 in it.
8-10k is a big arsed FAIL in my book for the amount of outlay to HP.
Jes
Posted: Wed Aug 05, 2009 9:56 am
by JenoNT
Thanks champs for the replies, really appreciate it!
One of the problems with living in Darwin is we don't really have a performance diesel workshop up here. Yes we have a place that has a 4wd dyno and they do pumps and injectors but they won't/don't do any sort of research or look at anything that is not tried and tested. Don't get me wrong, they are good blokes and they do a good job, but they are not really into PERFORMANCE type work.
Matt.Mcminn, thanks for the post, you blokes are definately into it in a big way! Great work, when would you have that set up available in "kit form" and would it marry up nicely to a garrett turbo?
Thanks again blokes, I'll let you know how I go!
Posted: Wed Aug 05, 2009 2:27 pm
by coxy321
If you're half handy working on your own car, you can just buy a "package" from Matt/Andy and bolt it on yourself.
I know Andy does a full ball bearing upgrade kit already.
Laminova kit= $3000
BB turbo upgrade= $2000
Already have exhaust.
Pump mods roughly= $1500
Dyno time= $500
Very roughly, $7000. Would "probably" net 150-170rwkw.
Posted: Thu Aug 06, 2009 8:10 pm
by matt.mcinnes
JenoNT wrote:Thanks champs for the replies,
Matt.Mcminn, thanks for the post, you blokes are definately into it in a big way! Great work, when would you have that set up available in "kit form" and would it marry up nicely to a garrett turbo?
Thanks again blokes, I'll let you know how I go!
Bolt on version available now tested this week on an auto with the same results as Marin's, just look different due to been an auto.
http://www.outerlimits4x4.com/ftopic164122.php
As for supporting bigger HP mine comes in at 244 rwhp approx oh and this one 596 rwhp we did in the USA.
http://www.youtube.com/watch?v=cpkCSykgt1s