Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

v6 coversion, engine mount alignment (stuck)

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Post Reply
Posts: 33
Joined: Tue Jun 23, 2009 8:46 pm
Location: SA

v6 coversion, engine mount alignment (stuck)

Post by Tonka tuff 4x4 »

my mate and i are putty a v6 in his 85 hilux dual cab, we bought the kit second hand which it came out of a hilux 4runner, now the right hand engine mount is out by 60 mm, we have the left one which is a marks adaptors one, not welded on yet.
will we need to customise the right one? or should it bolt up to the original hilux mount.
is the hilux 4runner 86 model chassis different lengh then the85 hilux dual cab?
and help would be much appreciated
Posts: 632
Joined: Wed Sep 07, 2005 8:59 pm
Location: South Gippsland

Post by hiluxmad »

the 86 runner is probably IFS.
the hilux dual cab will be solid front axle.
the engine mounts are different positions between petrol and diesel so depends on what the kit was for originally and what it is going into.

i beleive thet deisel models line up but the y series petrols do not.
check the marks website im pretty sure the info is on there...
Keep it shiny side up!
Now doing general fab work and painting
trays, trailers, engine swaps on request, some tube work, silo section sliders, rust repairs, ute chops etc
Posts: 33
Joined: Tue Jun 23, 2009 8:46 pm
Location: SA

Post by Tonka tuff 4x4 »

the 4 runner is LFS front, but it may have been diesel, our dual cab is petrol, yeah i looked at marks adaptors, so i guess we will have to get the right hand bracket from marks,
cheers for the reply buddy
Posts: 100
Joined: Tue Aug 18, 2009 7:02 pm
Location: south coast

Post by optima »

depends wat gear box you are yousing an wat bell housing. with myn i had to get engine mounts from dellow automotive once you work out wat you need just bolt the bear box up the the engine then bolt it in with the cross member then raise or lower the engine to were you want it . hop this helps
if its got t#ts or tyres your gunna have trouble with it
Posts: 143
Joined: Sun Oct 22, 2006 9:33 pm
Location: Inner West, Sydney

Post by dawg runner »

All i can say is do not use the marks adapter for the left side ( passenger side ) if you want to run crossover steering because you will need to booty fab it.

Right hand bracket ( drivers side ) I just chopped mine out and got the bracket from marks but in hindsight i would have just gone to wreckers and cut one out of another chassis and put it where you need it. Marks kit is $250 for both so not sure what it would be for 1 but i could only imagine it would be around the $100 mark. Correct me if i am wrong.

Hope this helps

Cheers

Dave
"There is gold in them there hills"
Posts: 33
Joined: Tue Jun 23, 2009 8:46 pm
Location: SA

Post by Tonka tuff 4x4 »

the conversion came with the left hand side from marks adaptors, we have already cut the original mount away from the left hand side, we decided to purchase a right hand side to see how it goes, the gearbox is a g52 and the bellhousing is from mark's adaptors, cheers for the reply fella's
Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest