Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
multi offset rim
Moderators: toaddog, TWISTY, V8Patrol, Moderators
multi offset rim
is there such a rim made that you can run both ways round so you could have a -44 offset and a +44 offset just by spinning them
Rims flipped from $50
rim
yeah but that would be a bit obvious and another set of bolts to come loose.
Rims flipped from $50
Havent seen it on luxs etc and not with an offset as large as 44mm but some rims can be flipped, they need a very flat plate, not curved like you see on hilux sunnies.
My mates sierra rims can be run both ways - they have the stud counter sink on both faces.
My mates sierra rims can be run both ways - they have the stud counter sink on both faces.
*there's a rock, drive over it :) there's a bigger rock, drive over it :twisted: there's an even bigger rock, oops broke it :oops: Upgrade broken bit :bad-words:
Goto *
Goto *
Re: multi offset rim
The thickness of the centre would kick in so it would be +44 vs -28 (or whatever) wouldn't it? Not that this matters.stock 4runner wrote:is there such a rim made that you can run both ways round so you could have a -44 offset and a +44 offset just by spinning them
There might be some alloys that would be able to do this out of the box I would think, although they might look shiat.
This is not legal advice.
If you went to a 3-piece rim then anything is possible.
The issues with just swapping the rim over are:
1. Enough spacing on the rim face to clear brakes when flipped
2. Nut style, would need to be tapered on both side of the rim, or mags machined on both sides.
3. Air valves are generally on one side of the rim, which is easily resolved if running tubeless tires.
Assuming that you address these three, there is no reason.
- David.
The issues with just swapping the rim over are:
1. Enough spacing on the rim face to clear brakes when flipped
2. Nut style, would need to be tapered on both side of the rim, or mags machined on both sides.
3. Air valves are generally on one side of the rim, which is easily resolved if running tubeless tires.
Assuming that you address these three, there is no reason.
- David.
Need a bigger shed...
Pardon my ignorance but how would you pump up your tubeless tyres without a valve of some sort somewhere?Dirty wrote:If you went to a 3-piece rim then anything is possible.
The issues with just swapping the rim over are:
1. Enough spacing on the rim face to clear brakes when flipped
2. Nut style, would need to be tapered on both side of the rim, or mags machined on both sides.
3. Air valves are generally on one side of the rim, which is easily resolved if running tubeless tires.
Assuming that you address these three, there is no reason.
- David.
George Carlin, an American Comedian said; "Think of how stupid the average person is, and realise that half of them are stupider than that".
I assume he means two valves, one on each side? Easy with tubeless.DAMKIA wrote:Pardon my ignorance but how would you pump up your tubeless tyres without a valve of some sort somewhere?Dirty wrote:If you went to a 3-piece rim then anything is possible.
The issues with just swapping the rim over are:
1. Enough spacing on the rim face to clear brakes when flipped
2. Nut style, would need to be tapered on both side of the rim, or mags machined on both sides.
3. Air valves are generally on one side of the rim, which is easily resolved if running tubeless tires.
Assuming that you address these three, there is no reason.
- David.
This is not legal advice.
Re: valve
its a total pia on the sierrastock 4runner wrote:the valve would not be an issue to me
*there's a rock, drive over it :) there's a bigger rock, drive over it :twisted: there's an even bigger rock, oops broke it :oops: Upgrade broken bit :bad-words:
Goto *
Goto *
rim..
why...
Assuming you want the offset for 4x4 work, you shouldn't need the taper on that side, if you do want it, double taper the holes..
no need to run a thick centre or double the holes..
Assuming you want the offset for 4x4 work, you shouldn't need the taper on that side, if you do want it, double taper the holes..
no need to run a thick centre or double the holes..
Just want to play...........
It would be worth it if you had some benefit from the extra track width off-road, but wanted to be strictly legal on-road. Less hassle than a second set of wheels.
Pity you can't just flip them to change the diameter.
How good would it be if someone invented "tread wraps", like snow chains but actually a second inflatable tyre that wraps around your 31" ATs and turns them into 35" extreme mud terrains. Slip them on, pump them tight, and off you go.
Pity you can't just flip them to change the diameter.
How good would it be if someone invented "tread wraps", like snow chains but actually a second inflatable tyre that wraps around your 31" ATs and turns them into 35" extreme mud terrains. Slip them on, pump them tight, and off you go.
This is not legal advice.
Who is online
Users browsing this forum: No registered users and 6 guests