Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

help installing suspnsion lift in vitara

Tech Talk for Suzuki owners.

Moderators: lay80n, sierrajim

Forum rules
Post Reply
Posts: 736
Joined: Sun Jan 30, 2005 2:32 pm
Location: brisbane

help installing suspnsion lift in vitara

Post by gumtree »

im going to install new lifted springs and shocks in my 93 LWB vitara. anything special i should know before or is this a fairly straight forwad task?

my main concern is do i need some kind of spring compressor to get the new lifted springs in their positions? new springs will lift the car 50mm.
1993 LWB vitara, Front & Rear alloy bars, towbar, spotties, UHF.
Top
Posts: 445
Joined: Mon Feb 11, 2008 9:54 pm
Location: Perth

Post by PCRman »

I can get my lifted OME springs in and out of my vit (with a 30mm spacer) with out a spring compressor but I have to, disconnect strut, disconect sway bar and pull CV out (RH side) and unbolt CV (LH side). I tried borrowing a spring compresor but the one i used was not well suited to the diameter of the OME springs I was installing.

Hope it helps!
Give a man a fire and he's warm for the day, but set fire to him and he's warm for the rest of his life

'02 NM GLS 3.2DID ARB bar Bushskinz steps Rhino bars front air locker OME susp 265/75R16 AT's
Top
Posts: 127
Joined: Thu Apr 12, 2007 7:30 pm
Location: central coast

Post by saffrett »

just unbolt sway bar and the 3 bolts on the ball joint lower it on a jack slip spring out new one in the jack back up and do bolts up again
1990 lwb vit
4 in lift
winch,lockers,gears, 31's
Top
Posts: 133
Joined: Thu Aug 03, 2006 3:39 pm
Location: East Brisbane

Post by bugden23 »

When i put spring spacers ontop of my lifted coils i used heavy duty wire to make a spring compressor, alot less fuss then pulling the whole assembly apart.

However, i will say that you have to make sure you're very careful how you tie the wire and where you place it. ....safety first peeps
Top
Posts: 736
Joined: Sun Jan 30, 2005 2:32 pm
Location: brisbane

Post by gumtree »

i have to take out my cv's to regrease and put on new rubber boots so i will drop the whole assembly down.
1993 LWB vitara, Front & Rear alloy bars, towbar, spotties, UHF.
Top
Posts: 117
Joined: Thu Mar 23, 2006 4:48 pm
Location: Redbank Plains

springs...

Post by error »

If you are looking for a new home for the old springs, I know a swb vit that they can go under....

Happy to give you a hand if you are near Ipswich....

Russ 0408871083
Just want to play...........
Top
Posts: 41
Joined: Mon Oct 26, 2009 10:38 am
Location: WOLLONGONG

Post by shane1992 »

Yo yeah you defo dont need coil compressors, I went out and brought a pair cost me friggen $100 and then when I went to do it they wouldnt even fit around them, just undo everything like sway bar, cv's drop the dif down etc,and your good to go ;)
Top
Post Reply

Return to “Suzuki”

Who is online

Users browsing this forum: No registered users and 2 guests