"Broken" Vitara tailgate handle solution
Posted: Tue Mar 02, 2010 4:06 pm
Hi all,
I thought I'd better make a contribution as I just had a win with my Vitara tailgate handle which I thought I would have to replace, and I'm sure many Vitara owners have experienced what was happening to me.
Not one to be beaten, I thought I'd remove the handle and see what was actually broken, and see if it was repairable or able to be braced before going ahead and ordering a replacement (even though they can be bought for $28 + postage on ebay).
I'm glad I did, because the fault was very simpy fixed, and didn't cost me a cent.
Many (most) Vitara owners are familiar with the tailgate handle lifting up, and feeling really weak, then not doing much.
To remove the handle, its just a matter of taking the inner tailgate panel off, and then removing the three 10mm bolts that hold it to the door. You will also need to pop the pushrod that goes to the lock mechanism out of the handle actuator. The handle will then practically fall out.
When I removed my handle, I found that the pin which the handle pivots on had come loose and slid out of its proper position.
The lever which operates the lock pushrod is in two parts:
The outer section (a kind of square tube) is part of the actual handle that you hold onto on the outside of the door.
There is then an inner, solid part that slides into the square tube of the handle. This solid bit is the part that your lock pushrod attaches to.
The solid inner part is held inside the square tube bit by the hinge pin passing through it. When this hinge pin dislodges itself and slides out, it allows the inner & outer parts to separate, thus partially or wholly disabling the handle.
If you were to keep yanking on it in this state, it would be very easy to break the square tube section, as its only plastic at the end of the day.
Whilst the solution to this problem is to simply re-assemble the lever/hinge pin, the pin is only held in place by the fact that it has a spline at one end that is supposed to grip on the plastic stands it slides through. I put a fairly substantial dob of Araldite on this spline to ensure that it doesn't slide out easily anymore.
You will also most likely need to re-hang the handle return spring onto its little supports so that the handle has tension on it again instead of flopping around. This will be pretty obvious when you're looking at it all, as the spring will just be hanging in the breeze with the supports at each end of it.
Whilst I had it all apart, I took the opportunity to silicon spray the lock parts.
My handle was then re-installed and feels better than new. It operates really well again now.
I thought I'd better make a contribution as I just had a win with my Vitara tailgate handle which I thought I would have to replace, and I'm sure many Vitara owners have experienced what was happening to me.
Not one to be beaten, I thought I'd remove the handle and see what was actually broken, and see if it was repairable or able to be braced before going ahead and ordering a replacement (even though they can be bought for $28 + postage on ebay).
I'm glad I did, because the fault was very simpy fixed, and didn't cost me a cent.
Many (most) Vitara owners are familiar with the tailgate handle lifting up, and feeling really weak, then not doing much.
To remove the handle, its just a matter of taking the inner tailgate panel off, and then removing the three 10mm bolts that hold it to the door. You will also need to pop the pushrod that goes to the lock mechanism out of the handle actuator. The handle will then practically fall out.
When I removed my handle, I found that the pin which the handle pivots on had come loose and slid out of its proper position.
The lever which operates the lock pushrod is in two parts:
The outer section (a kind of square tube) is part of the actual handle that you hold onto on the outside of the door.
There is then an inner, solid part that slides into the square tube of the handle. This solid bit is the part that your lock pushrod attaches to.
The solid inner part is held inside the square tube bit by the hinge pin passing through it. When this hinge pin dislodges itself and slides out, it allows the inner & outer parts to separate, thus partially or wholly disabling the handle.
If you were to keep yanking on it in this state, it would be very easy to break the square tube section, as its only plastic at the end of the day.
Whilst the solution to this problem is to simply re-assemble the lever/hinge pin, the pin is only held in place by the fact that it has a spline at one end that is supposed to grip on the plastic stands it slides through. I put a fairly substantial dob of Araldite on this spline to ensure that it doesn't slide out easily anymore.
You will also most likely need to re-hang the handle return spring onto its little supports so that the handle has tension on it again instead of flopping around. This will be pretty obvious when you're looking at it all, as the spring will just be hanging in the breeze with the supports at each end of it.
Whilst I had it all apart, I took the opportunity to silicon spray the lock parts.
My handle was then re-installed and feels better than new. It operates really well again now.
