Page 1 of 1
hilux drive shaft center dealy...
Posted: Wed Mar 24, 2010 8:34 pm
by S.CoXy
OK. Just blew the arse out of my center bearing on my YM67 project car. Car has 2" load carying leafs (handles like a gokart with no load), I installed a new one when I got rego and since then have ran in down the hwy for 3000k ( bris to melb x2) and a few short road trips @ total 1000kish ( driving it like i stole it ). Have I missed somthing when i installed it or is the hwy Ks just asking to much for a lifted truck??? or other?
Posted: Wed Mar 24, 2010 9:44 pm
by bugshifter
I have found the center bearings hold up better if you fill the outer rubber with Sikaflex. Seem to hold them together longer
Posted: Wed Mar 24, 2010 9:57 pm
by S.CoXy
Sikaflex is there anything it can't fix??? It holds half the panels on my truck any way why not use it there........... Lost the whole center so that might work.
Am thinging about some blocks to line the bearing up with the drive line too????
Posted: Wed Mar 24, 2010 10:07 pm
by hiluxmad
when you replace the center bearing space it down about 10/15 mm improves the angle and stops it chewing out. even a 2" lift on a hilux needs this
Posted: Wed Mar 24, 2010 10:26 pm
by S.CoXy
when you replace the center bearing space it down about 10/15 mm improves the angle and stops it chewing out. even a 2" lift on a hilux needs this
Just down or on a angle? Do have all the kit or do the standed RUF and IFS rear leaf and diff conversion that will bet going on it soon, just worried it already chewed out...
Posted: Wed Mar 24, 2010 11:10 pm
by KaMo
I just had the two piece shaft made into a single shaft using the old unis and slip yoke. Cost me $250 bucks. Smooth as now...no more bearing to flog out...and cheaper than a genuine replacement bearing. But the vehicle is a tourer not a comp rig, so this option may not suit you for whatever reason.
Posted: Wed Mar 24, 2010 11:35 pm
by hi_luxmad
get a 1 piece made up.
although ive nver had a problem with mine and ive run 35s with a bit more that 2'' spring lift
Posted: Thu Mar 25, 2010 7:04 am
by brad 93hilux
tried heaps of stuff and after the 4th one i went a 1 piece tail shaft..
No problems now
Brad
Posted: Thu Mar 25, 2010 3:44 pm
by hiluxmad
as said go a one piece if your doing more mods.
you only need to space it down if you are keeping the two peice it improves the angle of the bearing
Posted: Fri Mar 26, 2010 4:24 pm
by S.CoXy
How much clearance to you loose by going single piece?
Re: hilux drive shaft center dealy...
Posted: Wed Feb 08, 2012 6:03 pm
by xj33
anyone know were i can get a one piece tail shaft and how much
Re: hilux drive shaft center dealy...
Posted: Thu Feb 09, 2012 11:22 am
by the_4br
when u do ifs rears a 167 tailshaft fits strigh in on a dualcab dont no bout the other wheel bases
Re: hilux drive shaft center dealy...
Posted: Fri Feb 10, 2012 10:09 am
by BlueSuzy
Or ebay. There is a few guys on there, custom length, $400
Re: hilux drive shaft center dealy...
Posted: Mon Apr 09, 2012 12:59 am
by Elmo
You dont need to go a single shaft to make it last, I hate single shafts with a passion due to the lost clearance on ramp over angle..
Just put a double cardon shaft in, I been running mine for easy 2 years with lockers, 35's minimum everyday and upto beadlocked 37' s at times etc etc and do some bloody HARD wheeling then turn around and commute 225kms daily for work (on 35's) and i've only ever ruined centre bearings when i've smashed them with a direct hit on rocks/ledges, NEVER have I 'worn' one out from the angle
Re: hilux drive shaft center dealy...
Posted: Mon Apr 09, 2012 6:00 am
by MissDrew
A single tail shaft gives the drive a much more direct feel to it, less vibs, less moving parts to fail.
The clearance differances between a split shaft and a single shaft is next to none.
In my Hilux I have run a single rear shaft for over 10 years now.
Never wasted a rear shaft.
Have walked the rear of my lux sideways on the shaft many times.
Just be sure to use a extra heavy duty walled shaft.
Re: hilux drive shaft center dealy...
Posted: Mon Apr 09, 2012 12:18 pm
by stan
if you decide to go two piece sharft ,have one in wynnum good condition asking $120 ph 0415672822