stage 1, got the turbo

[biegetroopy]

well the turbo has arrived[gt2876r], now for the fun part didnt think it would be quite so HUGE!!!!

[yamaha__308]

Yeeeahh.. That's what she said..

[Z()LTAN]

hehe told ya!

Go through my thread mate, its got all u need to know about fitting it there.

Have fun with the 4" inlet pipework!

[toyotasrtuff]

still wont beat the nissan mick;;;; ha ha;;;;dazza

[biegetroopy]

if i use reducers 4" down to 3" then to the original 2 3/4" on the air filter box is that going to be a bad thing???

[tiny80]

you will loose some power and lag poss it will only come into effect in high hp turbo set up

[Z()LTAN]

depends on how deep you set the fuel.

I sucked a 4" POD filter flat with mine.

[biegetroopy]

ordered the dump pipe flange today ill get some 3" tube tomorrow,that should be done by next weekend!!

[matt.mcinnes]

The new batch will be in by Friday, with your name on one.

[biegetroopy]

let me know and ill be there with bells on

[rowenb]

That adapter looks like ally or is it just a nice machine finish?

[matt.mcinnes]

That adapter looks like ally or is it just a nice machine finish?

It's a very nice finish in Steel

[biegetroopy]

braided oil line and sump return the way as well

[matt.mcinnes]

Fits a treat

[biegetroopy]

it is a thing of exquisite beauty!!!!

[biegetroopy]

next to do take of sump and hammer out dent from hidden stump,install oil return ,fit adaptor to oil pressure switch and run line!!

[biegetroopy]

oil fittings in sump ,sumps on, oil in, oil feed is teed off and working, rest now have lunch, take off exhaust manifold sarvo and bolt on exh an turbo hook up oil line and pipes should test drive tomorrow,hopefully??

[TheBigBoy]

Keep the reports coming...

[biegetroopy]

hit a snag exhaust nuts bit tight soaking in inox overnight try again tomorrow

[matt.mcinnes]

Curious to why your taking the exhaust manifold off, or do you mean the exhaust from the from the exhaust manifold. As I don't think you have any need to remove the exhaust manifold it's self?

Let's have some pics too

[biegetroopy]

bought another one so i could bolt it all together before putting it in the car!!didnt need to just did actally now sitting on the studs ready to tighten up

[ledgend80]

how did you go with the wastegate actuator did you have to modify the mount to get it to fit or not

[biegetroopy]

had to make new bracket and lenghten the throw on the actuator,but its all bolted in now ill run some pipers this week ,have to mod the heater water return pipe as it looks like it will be in the way of the exhaust

[Z()LTAN]

the steel part of my heater pipe misses by about 10mm. But im running a different manifold and an adapter plate too.

[biegetroopy]

im just gonna have t trim mine alittle

[biegetroopy]

moved the water line pipe, ran water lines hooked up oil lines just waiting on silicone bends ,exhaust on friday [3"with muffler or without???any suggestions????]should be going next weekend

[Z()LTAN]

GT2876r + no muffler = LOUD!

[80's_delirious]

muffler for sure, unless you like being looked at everywhere you go.

I fitted a 3" system to my factory turbo 80 and it was way too noisey with no muffler, sounded like a school bus with a broken manifold.

go the longest straight through muffler you can fit in. It will still sound beefy, but will take some of the noise out without affecting flow

[biegetroopy]

ok 3" with muffler ,ordered egt and boost gauges sunday with pillar pod

[erik121]

bieg troopy could u post some pictures of your setup please