Hello everybody...Ive got a big problem..but at first Infos to my car...
Toyota 4 Runner (LN61) 1988
Its an Import...2.4 litre Turbo Diesel
A friend of mine and me have replace the timing belt...including the tinsioner pully and the idler pully...The marking poinst have been alright.....after this one we have cleaned the Air filter...its a Uni....????? dont know the thing...but you used oil after cleaning and drying....i hope you know what i mean...but heres the problem!!!!!
I have absolutely no power....is such a big difference from before......there comes alot of smoke out of the exhaust....and it needs a lot of time before the engine is running.....rrrrhhhrrr....rhhhrrrr....and after 10 Seconds the engine starts...but you must push the gas pedal...ohterwise it turns off again.....and the Car is louder than before.....
the next problem is the turbo comes far too early....i was driving on the Highway with 80 Kmh with Turbo all the time....
Whats wrong....???? is the timing bad....must i adjust it???? Or it is anything with the Airfilter...maybe we used to much oil....Im very disspointed....it turned all in a nightmare....i
thx a lot...best wishes from Perth..
Maik
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
No Power after replacing from Timing Belt...Whats wrong???
Moderators: toaddog, Elmo, DUDELUX
Re: No Power after replacing from Timing Belt...Whats wrong?
sounds a bit like the timing is out, that would explain the lack of power, hard starting, and smokey exhaust. Mine did the same wen i changed injector pumps before the pump it self was tuned properly, and it also made the exhaust change notes and appear louder although it did still start easily. did u return all of the timing marks to top dead centre? although if the filter is chooked up with to much oil it may be starving of air, did u use the right oil for it and how did u apply it?, u can always check to see if its the filter simply by removing the air filter and give it a run with out it, it wont hurt it, just dont go without it for to long and dont leave the air box open for shit to fall in there, drive on a dirt road etc ( that will at least eliminate the filter from ur problem)
79 series cruiser, 6" susp., 3' body lift, rear coil conversion, 35" baja claws... fully engineered and lockers on the way
Re: No Power after replacing from Timing Belt...Whats wrong?
I'd suggest the timing (probably fuel pump) is out by 1 tooth. Easy mistake
Tetanus rolling on 37's
Re: No Power after replacing from Timing Belt...Whats wrong?
Thx for the answers.....you mean with fuel pump the injection pump, don't you....
I also think its the injection pump ....but at first i will remove the airfilte...so i can eliminate if the airfillter is the problem thx@tezza88
if is not the problem then i must check the timing marks again....the timings are following...camshaft gear 3o'clock, crankshaft gear 12o'clock and injection pump 12 o'clock....i hope thats okay...
How can i test it without a the f+++ing work(remove radiator, fan and so on)...
and when i turn the crankshaft gear (with timing belt) to test ....its okay so...or must i anything remove (glow plugs or something else)
okay....thx to you both guys
best wishes Maik
I also think its the injection pump ....but at first i will remove the airfilte...so i can eliminate if the airfillter is the problem thx@tezza88
if is not the problem then i must check the timing marks again....the timings are following...camshaft gear 3o'clock, crankshaft gear 12o'clock and injection pump 12 o'clock....i hope thats okay...
How can i test it without a the f+++ing work(remove radiator, fan and so on)...
and when i turn the crankshaft gear (with timing belt) to test ....its okay so...or must i anything remove (glow plugs or something else)
okay....thx to you both guys
best wishes Maik
Re: No Power after replacing from Timing Belt...Whats wrong?
late combustion? causing detonation to late and too much reaction happening within the dump pipe?
This might explain why the turbo is spooling earlier.
I would be advancing the injection pump one tooth and testing again.
Stuffing up the air filter could give you low power and smoke but would not be letting your turbo spool very well - so i think you can rule that one out.
This might explain why the turbo is spooling earlier.
I would be advancing the injection pump one tooth and testing again.
Stuffing up the air filter could give you low power and smoke but would not be letting your turbo spool very well - so i think you can rule that one out.
*there's a rock, drive over it :) there's a bigger rock, drive over it :twisted: there's an even bigger rock, oops broke it :oops: Upgrade broken bit :bad-words:
Goto *
Goto *
Re: No Power after replacing from Timing Belt...Whats wrong?
......juhu...done...it works....only one tooth at the injection pump...it starts immediatly and everything is fine....thx guys....
its a very good forum...see ya later with more troubles:D
Mike
its a very good forum...see ya later with more troubles:D
Mike
Who is online
Users browsing this forum: No registered users and 1 guest