Page 1 of 1
who has fitted a gt2860 to a 1hdt 80 series
Posted: Tue Apr 12, 2011 4:21 pm
by scottmcguinness172
hey all im lookin at putting a garret gt2860 on my 1hdt i know i need to make a new manifold is there any problem of it fitting inbetween the block and manifold?
i have been told they have to be pulled apart on a bench and put back together on the car as they are 2 big to fit in as 1 unit.
i have been looking aorund and looking for info but i cant find much any help or pics would be awesome
cheers
Re: who has fitted a gt2860 to a 1hdt 80 series
Posted: Tue Apr 12, 2011 4:26 pm
by hulsty
Re: who has fitted a gt2860 to a 1hdt 80 series
Posted: Tue Apr 12, 2011 4:34 pm
by scottmcguinness172
yea i read that have you still got the adaptor?
Re: who has fitted a gt2860 to a 1hdt 80 series
Posted: Fri Apr 15, 2011 9:30 pm
by ledgend80
when i fitted my gt2871r i got one of matt mcinness adaptors. problems i encountered when removing the ct26 from the manifold it would hit the engine mount but with a large pry bar i got it off, but i would advise removing the manifold complete with turbo and then remove the turbo and then fit the adaptor plate and then the turbo. problem i had when fitting the turbo is that the wastegate actuator would hit the engine block so i had to modify the the wastegate actuator mount and extend the the actuator arm to get it fitted. if i was to do this again i would seriously look at dieseslex modified ct26 as there will be a lot less work and cheaper with better results if what dieslex is stating is true. (no reason to doubt it here)
Re: who has fitted a gt2860 to a 1hdt 80 series
Posted: Fri Apr 15, 2011 10:57 pm
by scottmcguinness172
hmmmm i dont know what to do atm my ct26 wont last long i dont think
Re: who has fitted a gt2860 to a 1hdt 80 series
Posted: Fri Apr 15, 2011 11:18 pm
by ledgend80
why not have a chat to dieslex and see what it is going to cost for his modified turbo. don;t think you would get much change out of $2500 to $3000 fitting at gt2860 or similar
Re: who has fitted a gt2860 to a 1hdt 80 series
Posted: Fri Apr 15, 2011 11:25 pm
by scottmcguinness172
cheers mate will do
Re: who has fitted a gt2860 to a 1hdt 80 series
Posted: Sat Apr 16, 2011 7:40 am
by 80's_delirious
scottmcguinness172 wrote:hmmmm i dont know what to do atm my ct26 wont last long i dont think
dont wait too long then. I had one blow, it disintegrated into little bits and wrecked teh engine also
Re: who has fitted a gt2860 to a 1hdt 80 series
Posted: Sun Apr 17, 2011 6:21 pm
by scottmcguinness172
cheers bud i sent dieselex an email but has not replyed as yet so ill wait and see what happends
Re: who has fitted a gt2860 to a 1hdt 80 series
Posted: Wed Apr 20, 2011 8:26 pm
by ljmonsta80
did you get on too dieselex what was there opitions
Re: who has fitted a gt2860 to a 1hdt 80 series
Posted: Thu Apr 21, 2011 1:21 pm
by CustomTurbos
So sorry, will reply now
Re: who has fitted a gt2860 to a 1hdt 80 series
Posted: Thu Apr 21, 2011 4:52 pm
by Glux
Do you these turbos really work that well and make that much difference?
Re: who has fitted a gt2860 to a 1hdt 80 series
Posted: Sat Apr 23, 2011 8:34 pm
by TheDato
Hi all,
I have a Dieselex CT26 on my 1HDT. To say that I'm happy would be an understatement. It spools by 1200rpm and pulls strongly from 1400rpm. It's early days for me because I went from a 1HZ to a rebuilt 1HDT and put this turbo straight on. So no before and after impressions. I've only got 1000k's on the motor so far and have yet to tune fully and fit an intercooler but initial impressions are very good, and it bolts straight on.
Again, not a direct comparison, but I had a GT2860 on my previous GQ TD42 and the modded CT26 walks all over that for boost response.
Sorry, no science involved at this stage, no dyno runs etc, only seat-of-the-pants. I'm happy.
Cheers
Muz