Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
80 series clickin of accelaration
Moderators: toaddog, Elmo, DUDELUX
80 series clickin of accelaration
Hey guys, i went for a bit of a hard drive last weekend and eneded up busting the drive flange off the hub on the driver side. I thought that this was not a problem as it has heppened before funning 35" tyres and a front locker, but now that i have replaced the hub i noticed under soft or hard accelaration (not holding a speed or slowing) i get a clicking noise. my orignal thought was the uni joints being dry so i pumped them full of grease and tryed it again.
Noise is still there.
So i removed the front tail shaft and now its gone, but the uni joints and all solid as.
So what i am now wondering is is it likely to be in my gearbox? or maybe crown wheel and pinion or maybe my cv's even?? i Run longfield cv's so i hope its not that and it feels like you can feel the clicking through the gear stick, thats y i thought uni's....... im going to borrow a front shaft and see if that might be it but are 80's knowen for damaging there gearbo's like this or should i be looking elsewhere for the cause?
Noise is still there.
So i removed the front tail shaft and now its gone, but the uni joints and all solid as.
So what i am now wondering is is it likely to be in my gearbox? or maybe crown wheel and pinion or maybe my cv's even?? i Run longfield cv's so i hope its not that and it feels like you can feel the clicking through the gear stick, thats y i thought uni's....... im going to borrow a front shaft and see if that might be it but are 80's knowen for damaging there gearbo's like this or should i be looking elsewhere for the cause?
80 Series ute 4.5L,3" exhust, 4"lift , f&r air lockers, snorkel, duel batteries, 35"MTZ's, sliders,12000lbs winch, beer fridge and extra's
Re: 80 series clickin of accelaration
Is it full time. There's not a lot of clearance between tierod and uni joint on front shaft so tierod may be hitting I have done that before.
Get a mate to watch front shaft as you move forward slowly.
Get a mate to watch front shaft as you move forward slowly.
93 RV, 5 in tough dog lift, dobinsons shocks and coils, PA, dual fuel, many many oil leaks and a ton of character.
Re: 80 series clickin of accelaration
Yeah full time, there should be a shiny spot if it has been hitting, so I can look at that in the morning.
80 Series ute 4.5L,3" exhust, 4"lift , f&r air lockers, snorkel, duel batteries, 35"MTZ's, sliders,12000lbs winch, beer fridge and extra's
Resident Terrorist
Re: 80 series clickin of accelaration
Stock front prop shaft or double cardan?
Re: 80 series clickin of accelaration
its a stock shaft, have 4" lift but never had a problem with angle before. have had the lift about 2 and a bit years now
80 Series ute 4.5L,3" exhust, 4"lift , f&r air lockers, snorkel, duel batteries, 35"MTZ's, sliders,12000lbs winch, beer fridge and extra's
Re: 80 series clickin of accelaration
If it still does it after trying a different front shaft, id say chipped crown wheel or CV. Try dropping the diff oil and see if any chips of teeth come out.
80 series gear box are pretty tough, and I would expect a gear box problem to still show up with the front shaft out
80 series gear box are pretty tough, and I would expect a gear box problem to still show up with the front shaft out
RN wrote:pussy is out, its the log for me... Thank you Jesus.
Re: 80 series clickin of accelaration
FOUND IT! Crown wheel is missing a few teath, so there you go, what a bummer, any advice where to get 4.56 gears from?? locktup is currently out of stock and i would like to fix this asap, who else is worth talking to?
80 Series ute 4.5L,3" exhust, 4"lift , f&r air lockers, snorkel, duel batteries, 35"MTZ's, sliders,12000lbs winch, beer fridge and extra's
Re: 80 series clickin of accelaration
You could just import from states, bout a week an half wait
1993 80 series, 4" tough dog adjustable bb lift kit, LPG, 35" MTR'S
brooksy wrote:Branden Tagg.....He is the King of all f@rkups & a Gimps bitch after hours
Re: 80 series clickin of accelaration
When you change out your crown wheel pinion set make sure you convert it to a solid spacer on your pinion insted of the colapsible spacer.
Will make a world of differenece to the life of the gear set .
Exspecially if you drive it hard
Will make a world of differenece to the life of the gear set .
Exspecially if you drive it hard
Who is online
Users browsing this forum: No registered users and 0 guests