Outer Limits 4x4 Board

Doing the BL on my lux right now. I have jacked the passenger side up and got all blocks in except the front one. all mount bolts are undone but something is holdin the front and causing the whole vehicle to try and lift instead of the front of the body. Any ideas?????

not engine fan hitting the radiator shroud

not engine fan hitting the radiator shroud. or brake or battery lines holding tight

steering shaft

Brake and battery lines are on the drivers side. Will go and have a look, brb

Definately not, but can't see anything holding it??? Also would bunnings have the prescribed high tensile bolts???, the fastener places are shut but if I couls get the bolts today I may be able to finish it.

The steering shaft hasn't been loosened yet but its on the drivers side obviously so shouldn't pose a problem

Sometimes you need to lift both sides at once to clear things.
Try lifting the r/h side gently and see if this lifts the left.
J Top

have you pushed the old bolt out yet

The d/s front one is a lil tight, will go and remove em now Darren. Hope the cab doesn't want to slide without bolts in. brb again

If you still have the rear ones in on the drivers side it shouldnt slip off

juss moved the d/s bolt but to no avail. I can't for the life of me see anything else stopping it??

it won;t go anyware with the motor in the road.

Ok, I got the shits an kept jacking the body until it got there. So if there is a phantom part holding it I will find out later. Now to loosen the steering shaft and lift the d/s.

But does bunnings have tensile bolts Im still wonderingm don't wanna waste time going there if they don't have em.

heres an give em a call

that would help

Mon-Fri: 7am to 6pm,
Sat: 8am to 5pm,
Sun: 9am to 4pm
T: (02) 4954-5444
F: (02) 4954-5298

gtwebbie wrote:it won;t go anyware with the motor in the road.

would be good advice if the engine was connected to the body

If your going to buy them at bunnings you better get going closes in 10 mins

FUG you i mean't that it carn't slide forward with the donk in the road.

Why would I want to slide it forward

so did u get the bolts to finish it

Nah mate, will get them through the week. I have only lifted the p/s atm. the d/s is gunna be a bigger pita having to remove that sidestep then loosen the steering shaft and extend the fuel filler and breather. So I will get those blocks in and bolt it all up and then I will look at how I am gunna drop my radiator(brackets etc) then find someone with an oxy so I can bend my gearstick. I'll put some photo's up in the members section tonight when the old man emails em to me. The bottom of the side windows is above my shoulders and I'm 5'9" tall, the sills are now 750mm off the ground.

To drop the radiator??? Do I cut up some sheet metal and simply hang it off or what have any of you guys done??

P/S finished except bolts

My radiator is bolted in its orginal location just no fan shroud thats with a 2inch body lift

high-n-mighty have you gotten your bolts yet ???? if not try KC Harris there in melborne street Maitland or there is a place on industral drive (newcastle side of ingall street) that does nuts &bolts they would be cheaper than bunnings i think maybe even better bolts aswell i can get the name of the newcastle place this week if you want i pass it every day going to work but cant remember the name of it

Thanks for the info Revin. I arranged for that bolt place to stay open later the next day so I could go in after work and get my bolts. Then I rang CDA in braodmeadow and simply had them deliver my bolts the same day. Poetic justice is a great thing

Bodylift is all in now and ready to go. I have only now to drop the radiator but am waiting to get it back because I forgot that I left it hanging by one bolt while full of coolant and three days later the side had apparently de-laminated itself.

Heres a pic I took yesty, now I have to build the tray an front bar and Im back on the road.

wen i did my b/lift i didn't have to lift the raidator,
i just removes the lower half of the shroud, i was replacing the hoses n`e`way so i just got longer ones

i just used some 20x5mm flat bar, drilled 4 holes so i could bolt it 2 the body then sit the radiator where u want it and mark the hole psoitions on the flat bar thats bolted 2 the body.

pull the flat bar out and drill the holes, then i got some bolts the right size and welded them in the holes and ground them flat so that wen it gets bolted back doen the bolts stick out and u can put your rad on them and put the washers and nuts on and its all done..

BTW was it the flexy mine from the clutch slave cyl 2 the body holdin the passenger side down ?? i bet it was, ake a look and u will prolly find that the bracket on the body is al bent

I'll check tomorrow mate, it moved eventually. I couldn't for the life of me find it so I just kept jacking.