Outer Limits 4x4 Board

I have an idea how to build a (rear) Diff lock for our Roza’s.
To run this idea I need to know if the standard Diff (side gears and diff pinion) can be installed inside the LSD case.
Another thing I need to know if I can find the LSD Diff case assy and cover.
I know that LSD Diff isn’t so common but maybe???

oferoza

I am of no help to you but very interested... good luck.

some drawings from the service manual.

are the gear sides and the pinion shafts are the same??
if the answers for those Q are yes... and we can find
LSD case (or find the manufacturer...) i think the Diff lock for fez
is reachable.

oferoza

the idea is to engrave truck shaft to the roza's dimensions with extra spline for the lock dog... similar to the maxidrive and as seen in this pic

any suggestion will be regard and any problem that you observe...
if anyone have a solidworks (or same hardware) drawing of the axle and shaft it will be a great help.

oferoza

I can email you the factory service manual for the rear differential if you need... or do you have it already?

Croz wrote:I can email you the factory service manual for the rear differential if you need... or do you have it already?

the factory service manual i have in hand. but the draw there is just a sketch. no scale or full dimension...

p.s if anyone took pic of rear diff (and shaft) opened up it will help too.

oferoza

Have a look at this site- say they can make vacuum or air lockers to fit most diffs! Located in Melbourne.

http://www.mcnamaradiffs.com.au/products.html

murcod wrote:Have a look at this site- say they can make vacuum or air lockers to fit most diffs! Located in Melbourne.

I E-maild them. but if this is the case... how come there is no locked Roza and i mean with original axle
I guess the Mcnamara product will be very expensive

oferoza

I emailed them also, but their email doesnt work..

I called the workshop this morning but unfortunately the guy I spoke to said there was no daihatsu diff covered in their line up... Wasnt all that interested either. He suggested I try ARB...

You should have suggested he have a read of their website Croz- then asked him the same question again!

Yeah I mentioned what the web page notes, but he wasnt interested, this was the same time as I mentioned his email didnt work but I dont think he knew what I meant...


Ahhh.... well... it seems that people who know diffs dont know what Ferozas are... Dont get me wrong, the company seems to be excellent at what they do, just of no help to our needs.

So we're in the same start point... i can build customized diff lock but need some help...
If anyone took pic of rear diff (and shaft) opened up it will help.
Drawing of the raer axle (fully defined and scaled) will be great... even just the shaft tail (the other side of the spline section).
Another important thing... what is this "line" at the drawing of the axle?
can this "line" desturb to the new shaft with the extra spline section?? (will be thicker alittle...)

If tou cant see the pic go to RS-4...

oferoza

From: "Jeff McNamara" <mcnamara@mira.net>
To: <ofer_feroza@yahoo.com>
Subject: Re: Vacuum Differential Locking Unit &/or Locking Carrier
Date: Tue, 31 Aug 2004 13:17:08 +1000


Sorry, we don't sell that part.
Regards.
Jeff


----- Original Message -----
From: ofer
To: mcnamara@mira.net
Sent: Tuesday, August 31, 2004 1:07 AM
Subject: Vacuum Differential Locking Unit &/or Locking Carrier


Do you have one that fits to Daihatsu Feroza F300??
thanks Ofer

Maybe they dont have that part... but have very fast service

oferoza

Don't know if this is any help but i've a mate who is an industrial designer who uses solid works and has it on his home PC. I'm sure i'd be able to get him to help if i could provide him with what to create.

Dave

Dangerous Dave wrote:Don't know if this is any help but i've a mate who is an industrial designer who uses solid works and has it on his home PC. I'm sure i'd be able to get him to help if i could provide him with what to create.

Dave

It can be a great help. I'm now trying to find rear shaft to take dimensions... i dont want to take out mine...
I'll be in touch after it's all in my hand.

oferoza

I dont no about the rest of the list, but I would pay any thing for a locker of any sort..
Please make my dreams come true!

marc wrote:I dont no about the rest of the list, but I would pay any thing for a locker of any sort..
Please make my dreams come true!

Haultech traction control Search for it if you don't know what it is

For the $ a lot of you guys will be lookin at for a custom diff lock you can get traction control f & r About $2500 it'll be like havin both ends locked

One n your midst is already lining up for it