Outer Limits 4x4 Board

is $1100 fitted a rip off?

its about the going price to lift everything up with it - bullbars, rear bar, sliders if attached to chassis and the cost of fitting and removing everything.

FYI....

blocks... 100 bux(piece of steel cut into lengths and drilled)
bolts ... 50 bux
carton of piss - 30 bux
another carton of piss/bottle of spirits for mate to do front and rear bar cut and weld to suit - 50 bux

all up works out to be 230... i'd budget 250 for something like this and i reckon you'd have a bit of change.

1100 is steep, but you get what you pay for... does that include engineering??

TOM

Ritter's quoted me about the same, $1000 approx.
The Rangie Spares kit is $500, and then all it takes is your time!
But you do need to weld for that kit, and your front/rear bars, sliders will still need modifying.

If you really don't want to do anything, then $1000 to cover everything isn't too bad a quote.

Give Ben a call at Rangieworx on 0416 046 844

The last time I checked Graeme Cooper automotive had a 2 inch lift for around the $230 mark, including bolts and new rubber mounts. You still need to make up the rear seatbelt mounts and so forth.

I would say with that kit about $300 total after you get the bits. Some welding required as all have mentioned here.

Regards,

Trav

i just got a 2" lift and fiberglass flares flares fitted for $1200 at hardcore 4x4 in mitcham Ph 9872 3133

muppet_man67 wrote:is $1100 fitted a rip off?

try rangieautomotive
9739 6989

there body lifts are quite cheap and they do a lot more extra like welding in blocks on parts of the chassis but i know they are under $800

but call to check speak with adrain.

No welding and kit inc aluminium blocks, bolts (hex head), nyloks, retainers (seat belt brackets) and load carrier blocks will cost you for up to 2" - $350, or up to 3" - $400 changeover on retainers.

Chassis extension block (60mm) for front bar is $150 and are weld on, but will fit most standard rangie bars. Dont need to buy new body mounts just swap the top rubber to the bottom, unless they are too worn.

I am currently out of stock but will have more in around the end of month at the latest.

Cheers
Ben

i may be wrong for other states but welding anything onto the chasis is illegal in NSW got pinged for it about 5 years back on my suzk

No welding and kit inc aluminium blocks, bolts (hex head), nyloks, retainers (seat belt brackets) and load carrier blocks will cost you for up to 2" - $350, or up to 3" - $400 changeover on retainers.

That's a good kit, and a good deal!
Rangie Spares kit has all that, but you have to weld on the load carrier blocks to the chassis rails, as well as the radiator spacers, but for $500.
I'd be choosing this kit if i had do it again.

i may be wrong for other states but welding anything onto the chasis is illegal in NSW got pinged for it about 5 years back on my suzk

Opps... too late!

BASSYK wrote:i just got a 2" lift and fiberglass flares flares fitted for $1200 at hardcore 4x4 in mitcham Ph 9872 3133

Did that include the flares and lift kit, or just the fitting?

LukeV wrote:

BASSYK wrote:i just got a 2" lift and fiberglass flares flares fitted for $1200 at hardcore 4x4 in mitcham Ph 9872 3133

Did that include the flares and lift kit, or just the fitting?

all included , i just dropped it off and picked it up

Seems pretty good, guess it is a bit cheaper for a two door. Still, you got it all fitted for ~$400 bucks Assuming that it was the RS kit and flares?

Luke

Can supply and fit body lift kit which includes all new brake lines and clutch line for $770 03 9739 6989

What about supply only, Kurmit?

And do you S1 Disco's?

Supply only on body lift kit $440