Outer Limits 4x4 Board

What is the track width of a narrow track sierra

What is the track width of a wide track sierra

Mick

Just goes to show post count doesn't represtent knowledge!


Search newbie


http://www.off-road.com/suzuki/techinfo.htm

You will find it under the year spec's. I didn't check myself though

DeWsE wrote:Just goes to show post count doesn't represtent knowledge!


Search newbie


http://www.off-road.com/suzuki/techinfo.htm

You will find it under the year spec's. I didn't check myself though

Yo pad whore do check it for yourself it says wide and narrow tracks are the same

That's why I got the sh!ts and posted this

I searched here too but couldn't find a definitive answer

to clarify it says tread of narrow and track width wide are the same but still doesn't answer the question

"Well i'm glad we sorted that out then".................tip toe quitely out of the room.

DeWsE wrote:"Well i'm glad we sorted that out then".................tip toe quitely out of the room.

-Mick- wrote:What is the track width of a narrow track sierra

What is the track width of a wide track sierra

Mick

Aren't you part way through the conversion??

Need to borrow a tape measure

bigsteve wrote:

-Mick- wrote:What is the track width of a narrow track sierra

What is the track width of a wide track sierra

Mick

Aren't you part way through the conversion??

Need to borrow a tape measure

Yeah but the wt diffs are at Damo's place so it'll have to be a loooong one

I wanted wms-wms measurements for each to see how much wider it'll be cause I just fitted these Grimace calmini flares I got off some old pos

and they give me HEAPS to fill, like my track will go another 5 inches per side I'm also getting my current rims cut and rewelded for more offset so trying to figure out how much I should go

Now stop whoring in my thread and only post if you know the answer No soup for you

i'll run a tape over mine tomorrow. i've got a NT and a WT set of diffs sitting next to each other so that it will be an easy job

Barathrum wrote:i'll run a tape over mine tomorrow. i've got a NT and a WT set of diffs sitting next to each other so that it will be an easy job

Thanks dude

-Mick- wrote:

bigsteve wrote:

-Mick- wrote:What is the track width of a narrow track sierra

What is the track width of a wide track sierra

Mick

Aren't you part way through the conversion??

Need to borrow a tape measure

Yeah but the wt diffs are at Damo's place so it'll have to be a loooong one

I wanted wms-wms measurements for each to see how much wider it'll be cause I just fitted these Grimace calmini flares I got off some old pos

and they give me HEAPS to fill, like my track will go another 5 inches per side I'm also getting my current rims cut and rewelded for more offset so trying to figure out how much I should go

Now stop whoring in my thread and only post if you know the answer No soup for you

Well with WT's and those flares and 15x7's with 2.5 inches of back spacing my 10.5 inch wide tyres were just at the edge of the flare.

cool thanks bigsteve

-Mick- wrote:cool thanks bigsteve

See.......................... who needs measurements

NT
Front 49 WMS
Rear 49 WMS

WT
Front 52 WMS
Rear 52 WMS

measurements might be a little out but not much. there only so much one person can do with a tape

Barathrum wrote:NT
Front 49 WMS
Rear 49 WMS

WT
Front 52 WMS
Rear 52 WMS

measurements might be a little out but not much. there only so much one person can do with a tape

Champ

might be worth putting into the general tech sticky

-Mick- wrote:

bigsteve wrote:

-Mick- wrote:What is the track width of a narrow track sierra

What is the track width of a wide track sierra

Mick

Aren't you part way through the conversion??

Need to borrow a tape measure

Yeah but the wt diffs are at Damo's place so it'll have to be a loooong one

I wanted wms-wms measurements for each to see how much wider it'll be cause I just fitted these Grimace calmini flares I got off some old pos

and they give me HEAPS to fill, like my track will go another 5 inches per side I'm also getting my current rims cut and rewelded for more offset so trying to figure out how much I should go

Now stop whoring in my thread and only post if you know the answer No soup for you

Just coz your junk is in my garage dont mean I am measuring stuff for you

Didn't ask you too not sure I'd be real confident in the result

-Mick- wrote:Didn't ask you too not sure I'd be real confident in the result

Now that you mention it I'm not confident those diffs are still there

Damo wrote:

-Mick- wrote:Didn't ask you too not sure I'd be real confident in the result

Now that you mention it I'm not confident those diffs are still there

nice