Page 1 of 1
Panel Beater to do Quarter Panel cut in South Brissy ? (GQ)
Posted: Mon Nov 08, 2004 5:20 pm
by Draven
Hey guys,
Just wondering if anyone knew of a Panel Beater / 4x4 shop that can cut my quarter panels for me ?
Thanks
Posted: Mon Nov 08, 2004 6:14 pm
by Daisy
redlands 4wd for southside
www.redlands4wd.com.au
and cris' 4wd accessories and suspension in caboolture (pm ludacris off this board)
TOM
Posted: Mon Nov 08, 2004 8:56 pm
by BigMav
Hey Draven once you get it done post back here with some pics of the job and what sort of cost it was. I'm still scared to cut guards after botching up previous 4b's.
Posted: Mon Nov 08, 2004 8:59 pm
by BigMav
Also another option other than cutting could be to bend the outer skin inwards so it meets the inner skin then cut the excess of the inner and weld together. Hope that makes sense, I think that way of doing it may leave a neater edge.
Posted: Tue Nov 09, 2004 1:15 pm
by MEX
ON TRACK 4WD at Slacks Creek cut and shut the rear quater panels as described by BIGMAV. I had mine done by them about a year ago for $400-ish, with me doing the repainting.
ON TRACK PH: 3290 2533
Regards MEX
Posted: Tue Nov 09, 2004 1:26 pm
by BigMav
You got any pics of the job mex? Price sounds reasonable enough.
Posted: Tue Nov 09, 2004 1:26 pm
by Draven
Hey MEX,
How did the cut come out ? Any chance of a couple pics ?
Posted: Tue Nov 09, 2004 1:28 pm
by BigMav
hehe look at the times of the last two posts. Only just beat ya to it
Posted: Wed Nov 10, 2004 8:20 am
by MEX
I will post a photo in the next few days. In short though it was a good job and well worth the money in my opinion.
Mex
Posted: Wed Nov 10, 2004 12:52 pm
by The Big Green Meany
MEX wrote:I will post a photo in the next few days. In short though it was a good job and well worth the money in my opinion.
Mex
Guys, There is a Beater at Albion ( Northside) Sorry ! but he is DAM GOOD , We all know how hard it is to get a good beater. Cut and plated mine and touched up the painted area around it for $150
only took 1 day
. I took the rear bar and flares off but he done the rest. He is behind Mc Donalds in Collingwood st Albion. Sorry Cant remember the name of the shop.
Posted: Wed Nov 10, 2004 1:24 pm
by BigMav
Even better for me being on the north side, you got some pics meany? 150 for each side or all up? My original bar is off and the new one is just itching to get bolted up.
Posted: Wed Nov 10, 2004 1:59 pm
by The Big Green Meany
BigMav wrote:Even better for me being on the north side, you got some pics meany? 150 for each side or all up? My original bar is off and the new one is just itching to get bolted up.
$150 all up
, No pics Im affraid it was on the shorty before I sold it, Now the waggons in getting a ute Conversion done!!!!!!
Posted: Wed Nov 10, 2004 2:35 pm
by CJ Burns Esq
Do you know of anyone in Sydney near liverpool that'll do the same?
CJ
Posted: Wed Nov 10, 2004 4:43 pm
by MEX
Sorry, I can't see how to attach the photo's. If you want them can you explain how to attach them or send me a PM with your email address and I will send them to you.
Regards MEX [/img]
Posted: Mon Nov 15, 2004 10:03 am
by BigMav
Posted: Mon Nov 15, 2004 10:06 am
by Draven
Just a quick question, was the corner damaged before the cut ?
Posted: Mon Nov 15, 2004 10:13 am
by MEX
Yes.
Left hand corner (one pictured) was crushed upwards 40-50mm.
MEX
Posted: Mon Nov 15, 2004 10:18 am
by Draven
Awesome..Thanks MEX...Im gona get onto Ontrack shortly.
