Page 1 of 1
Visual differences between 3.5 and 3.9 carby motors
Posted: Fri Jan 07, 2005 1:05 pm
by STIKA
Can anyone tell me of any visual differences between a3.5 and 3.9 carby motors
Posted: Fri Jan 07, 2005 1:27 pm
by RUFF
What Brett needs to know is there an external difference in the Block. Not including the engine Number. I know my 3.9 was obvious because it has the indexed(pin punched look) engine number commonly used in late model cars around the world now.This engine has letter stamped numbers but so did the early 3.9s. Brett has bought an engine and is not sure if it is a 3.5 or a 3.9. It has a Carbed manifold on it and he hasnt removed it to see if the heads have the slight cut outs for the injectors in the intake ports.
It is supposed to be a 3.9. Is there a way to tell externaly?
Posted: Fri Jan 07, 2005 6:55 pm
by p76rangie
There is no real way externally to tell the difference between a 3.5, 3.9, 4.0, or 4.6. As you can use 3.5 heads on any of these blocks, looking at the heads will not tell you much.
Posted: Fri Jan 07, 2005 7:03 pm
by landy_man
the 4.0 and 4.6 have a small opening on the lower side of the block...can't remember what for.. perhaps sensor...
but AFAIK their is no distinguishable difference between 3.5 and 3.9
grab engine number and search for listing
Posted: Fri Jan 07, 2005 7:34 pm
by Rainbow Warrior
landy_man wrote:the 4.0 and 4.6 have a small opening on the lower side of the block...can't remember what for.. perhaps sensor...
but AFAIK their is no distinguishable difference between 3.5 and 3.9
grab engine number and search for listing
Some 3.9 blocks like mine had about 4 more head bolt holes in the block each side than earlier heads, well at least mine did, 10 head bolts each side on my 76 heads and we could see the extra holes after assembly, I had no problems fitting a 3.5 timing cover & mainifold.
Posted: Sat Jan 08, 2005 8:52 am
by Bush65
Rainbow Warrior wrote:landy_man wrote:the 4.0 and 4.6 have a small opening on the lower side of the block...can't remember what for.. perhaps sensor...
but AFAIK their is no distinguishable difference between 3.5 and 3.9
grab engine number and search for listing
Some 3.9 blocks like mine had about 4 more head bolt holes in the block each side than earlier heads, well at least mine did, 10 head bolts each side on my 76 heads and we could see the extra holes after assembly, I had no problems fitting a 3.5 timing cover & mainifold.
Other way around - later heads have 4 less head bolts (10 vs 14).
Here is a pick of my 4.6 with 3.5 heads. You can see heads of bolts for cross bolted main bearing caps and the sensor opening that landy_man mentioned (cover fitted on flywheel side in my case).
Posted: Sat Jan 08, 2005 8:17 pm
by Rainbow Warrior
Bush65 wrote:Rainbow Warrior wrote:landy_man wrote:the 4.0 and 4.6 have a small opening on the lower side of the block...can't remember what for.. perhaps sensor...
but AFAIK their is no distinguishable difference between 3.5 and 3.9
grab engine number and search for listing
Some 3.9 blocks like mine had about 4 more head bolt holes in the block each side than earlier heads, well at least mine did, 10 head bolts each side on my 76 heads and we could see the extra holes after assembly, I had no problems fitting a 3.5 timing cover & mainifold.
Other way around - later heads have 4 less head bolts (10 vs 14).
Here is a pick of my 4.6 with 3.5 heads. You can see heads of bolts for cross bolted main bearing caps and the sensor opening that landy_man mentioned (cover fitted on flywheel side in my case).
Hmmm, maybe either my heads were later model than I thought or I'm just remembering wrongly from 7 years ago. The original block was supposes to be a Rover car motor, maybe the heads were too. Anyway, the 3.5 heads went well on the 3.9