Notice: We request that you don't just set up a new account at this time if you are a previous user. If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
My dad got an absolutely bargain, 3 Rav 4 alloy wheels at $5 each. Plus they're brand new. He originally got them for a trailer but they wouldn't fit or something. So he said I could have them... then I found out the bloody hubs are too big. They would have been nice too, 16".
They were selling quite a few of them, but when he went back for another one they were gone. Doesn't matter though as they don't fit.
I know its probably impossible but is there a way to make them fit ?
"It has the aerodynamics of a brick." - Comment about the Sierra by my dads mate.
im sure someone would be able to machine them out to fit
provided it will be strong enough
TOYZUKI 96 coily zook,lux diffs, 3 inch suspension lift,3 inch body lift, 33'sMTRS,series 4 hopper,power steer,twin air lockers,4 LINK front and rear,2 inch spacers(GOT WIDTH)
For $5 a rim it would be worth having a hack at it Or just sell them and get some wheels that fit your zook properly. But since you only have 3 anyway maybe they will be better on a trailer... At least the trailer will look cool, LOL!
Don't know if he'll let me have them hacked up, hes probably just going to sell them now. But yeah only 3 is a problem, I don't want to pay a lot for another new alloy if it might not even work.
Its annoying my dad didn't tell me that they were pretty much giving rims away, I found out a day later, when there are none left. I would have bought 4 or 5 just for the hell of it. If they didn't fit I could have made a profit selling them anyway.
A trailer with them on would be pretty cool though. But I'd hate it because a trailer has better rims than my car.
"It has the aerodynamics of a brick." - Comment about the Sierra by my dads mate.
I realise they aren't for Suzukis, I'm aware they don't fit. I was just curious if you could actually modify them to fit. From what I've gathered you can but its a bit iffy and sounds dodgy.
So no I'm not going to, I wasn't going to from the start unless it was easily done.
Yes I do know they have a different stud pattern but thats irrelevant when you consider the hub problem. Enlarging the hole for the hubs looks almost impossible as it would cut into the holes for the studs.
As for alloys, you may think they are gay. But compared to alloys I find steel rims very gay.
"It has the aerodynamics of a brick." - Comment about the Sierra by my dads mate.
At $290 a rim... Not f***ing likely! But they're close to what you probably want.... Or check out these cheaper (but not really that cheap) round steelies: http://www.onall4.com.au/USA_Steel_Wheels.htm
As for alloys, you may think they are gay. But compared to alloys I find steel rims very gay.
Compared to 15 x 10 steel beadlocked rims, they are super Grimace!
Rav 4's are Grimace
Perth is Grimace
and lastly grimace is Grimace
NOTE: I just broke the forum rulz...mod away Sam...ps: your Grimace
All of the above are still not as Grimace as your avatar Dewse !!! LMAO (please change it, its scaring me....seriously! )
Sorry I have had special request that I keep it the same for a little while so that I can be identified when scrolling through pages. It is a fully sick avatar I can understand if you are jealous. I will draw one for you if you like??
[quote="STD CONSUMER"]haha, i'm tellin you, my camp was hard to find on Saturday night!
then i shared my bed with 2 second tom... [/quote]
)
Or just sell them and get some wheels that fit your zook properly. But since you only have 3 anyway maybe they will be better on a trailer... At least the trailer will look cool, LOL!
