Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Tapered reamer

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 64
Joined: Wed Nov 20, 2002 7:41 am
Location: Melbourne, Australia

Tapered reamer

Post by vrunner »

Does anybody know where I could hire a tapered reamer or have a steering arm hole reamed out in Melbourne?

I am building my own high steer arms and need to ream a tapered hole to suit Patrol tie rod end.

I have looked at buying a reamer but it is going to cost over $150.00 and that's a bit too much for a single use.
Top
Posts: 5521
Joined: Tue Jan 13, 2004 12:09 pm

Post by mkpatrol »

Try the yellow pages. Most engineering fabrication shops will have them.
Don't ask me, ask them. I'm just runnin for my life myself.
Well they are all following you...
No they ain't, I'm just in front...............
Top
Posts: 671
Joined: Mon Aug 23, 2004 10:06 am
Location: Mornington

Post by YankeeDave »

what size, we've got a few here
Jeep Wrangler TJ

Jeep Cherokee XJ
Top
Posts: 207
Joined: Thu Aug 26, 2004 11:14 am
Location: Queensland,Clontarf

Post by Hales231271 »

Cheezy Racing can do it.
Top
Posts: 64
Joined: Wed Nov 20, 2002 7:41 am
Location: Melbourne, Australia

Post by vrunner »

Hey YankeeDave

What sizes do you have? In looking All I can find is flute length, max dia and min dia. None of the reamers listed were sized in degrees.

Also where abouts are you located?
Top
Posts: 671
Joined: Mon Aug 23, 2004 10:06 am
Location: Mornington

Post by YankeeDave »

lyndhurst, basically south dandy


off abbotts rd,

i'll go out in check in the tool room later for em
Jeep Wrangler TJ

Jeep Cherokee XJ
Top
Posts: 64
Joined: Wed Nov 20, 2002 7:41 am
Location: Melbourne, Australia

Post by vrunner »

Thanks mate.

I'm just round the corner in Quality drive!
Top
Posts: 671
Joined: Mon Aug 23, 2004 10:06 am
Location: Mornington

Post by YankeeDave »

what size shaft are you using so i get you the right one, and how long would you need it for?
Jeep Wrangler TJ

Jeep Cherokee XJ
Top
Posts: 275
Joined: Wed Aug 27, 2003 7:21 pm
Location: sunny melbourne

Post by 85lux »

i could not find a reamer when i did my hi-steer arms. i bored the taper in a lathe using bearing blue to get the taper right. it was a bugger of a job. i wish i had this info a while ago.
Top
Posts: 346
Joined: Sun Jun 22, 2003 6:23 pm
Location: Brisbane

Post by Yarno »

I bought a hand one from super cheep was about $10, bent the little handle on it but it did the job...
Go hard or go home!!!
MU build here
Top
Posts: 510
Joined: Wed Sep 15, 2004 7:07 pm
Location: Pheasant Creek

Post by HEY CHARGER »

Yarno wrote:I bought a hand one from super cheep was about $10, bent the little handle on it but it did the job...



Are you sure ???? :shock: :shock:
Top
Posts: 346
Joined: Sun Jun 22, 2003 6:23 pm
Location: Brisbane

Post by Yarno »

yeah I think it was about $10 or $20 from memory and I think it was about a 1:10 which was right for a crusier TRE...
Go hard or go home!!!
MU build here
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 0 guests